1974 FJ40 in Central CA

[D'Animal]

I have the frame.
Someone on the east coast PM'ed me and I told them I would not seperate. I will find the PM and see who posted first and forward it to you so you don't think there is any funny business going on.

I was hoping to sell it with the cowl but that doesn't look promising.

I will get it off and see how rusty it is on the bottom lip.

sorry I was looking for a frame.

 

[D'Animal]

Picture

How much is lower passanger (under the glovebox) pad? How much to ship appx to NC, 28806? Thanks

It has been cut when the PO installed the radio.




I will get a picture and post it to see if you are still interested.

 

[D'Animal]

I should have charged you labor.

Did you know there is a clip holding the upper bearing in?

Dan,

I am looking for part #23 in the attached link. It is the steering column support through the fire wall. Is is the square style not the earlier oval type.

http://www.sor.com/shared/image/098B.gif

I have it stil on the firewall.

Is there suppose to be a bushing or something in there?

No bushing, the column bolts to the mount with 4 bolts and the mount attaches to firewall with 3 bolts. There is a rubber gasket between it and the firewall. Bushing/gromett/gasket was used on the early (oval shaped) mounts.

It will go out with your box-o-stuff in the morning.

I hope this is the right one. Because you are getting it sent to you since it matches the picture in the link you posted.

 

[D'Animal]

The cable on the passenger side is frayed (sp?).


Mark at MArks off road has these cables for $20.00 on his site. 169-02 is his part number. There is a link a few posts down.

does the wiper motor and assembly still work if so how much shipped to AK 99506 please PM me back

Is there a trick to testing these or just hook up 12v and see if it moves?

 

[rockcod]

I hope this is the right one. Because you are getting it sent to you since it matches the picture in the link you posted.

Dan, that is it.

Thanks!!!

 

[D'Animal]

That is good, because I shipped it to you this morning.

Dan, that is it.

Thanks!!!

PM'ed you the tracking # as well.

 

[Straightjacket]

Do you still have the rear hatch? How good of shape are the latch mechanisms? You wouldn't have the hard doors would you? Please pm me with more info.

 

[D'Animal]

I connected it to 12v and both the high speed and low speed work.

The wiper link wire needs replaced. Mark has them for $20 under part # 169-02 on his site.

Catalogue Page 28

$125 plus shipping will get you both the motor and the link pivot, the spacers, 4 mounting bolts and the wiper arms. Basically everything but the wire going down the windshield.

does the wiper motor and assembly still work if so how much shipped to AK 99506 please PM me back

I will check the motor and the other gear setup when I get back home this weekend,

Is there a trick to testing these or just hook up 12v and see if it moves?

Let me know.

 

[D'Animal]

I have the complete 1974 wiring harness in very good condition removed. I unplugged the rear section going to the rear tail lights/fuel gauge. Other than that it is complete.

$80 plus shipping.

 

[Darby Darrow]

Dan,

Can I get next in line for the wiper motor?

And how much for the windshield glass? I found a frame.

 

[D'Animal]

I'll give AKFJ62 till sunday night to post up whether he wants it or not. Monday morning if he has not posted, it will go to you.

I just opened up the windshield last night. It is in mint condition as well as the windshield to cowl mounting gasket. I wish my 1976 was this rust free and gasket in this condition.

I plan on pulling the winshield today and will see how the windshield gasket is.

 

[Darby Darrow]

Thanks Dan!

 

[AKFJ62]

yes I do want it. pm sent

 

[65swb45]

Dan, I don't check this forum often. Just saw your thread. Interested in the manifold set. Can apply the rear taillights I've been holding for you to this.

 

[yosemitesamtlc73]

do you still have the wiper motor or did it go with the windsheild frame

 

[D'Animal]

do you still have the wiper motor or did it go with the windsheild frame

AKJ62 is getting the wiper motor assy.

 

[D'Animal]

A semi-local person is suppose to come and look at and maybe buy the intake/exhaust assy. This si the person I pm'ed you about.


I local Webelk6 sent me the taillight assy's last month. You can sell yours.

Dan, I don't check this forum often. Just saw your thread. Interested in the manifold set. Can apply the rear taillights I've been holding for you to this.

 

[D'Animal]

I will get it boxed up and ready to ship. My distribution center is closed until Jan 5 2009.

If you want, I can take it to a UPS regular location but the freight will be about 3x's as much.

yes I do want it. pm sent

We get a crazy rate from UPS since we fill at least one of thier semi-trailers a day.

 

[D'Animal]

The cowl is stripped and ready to ship.


$300 plus shipping from 93291.

This price included me palletizing it and making a crate for it.

If you pick it up, same price.

 

[D'Animal]

Windshield mount area.