replacement

Any alternatives out there besides SOR? TIA!

Hi All, we are new here, My 1998 LC Beulah has busted her timing belt and my mechanic isn't interested in replacing it, he says "it's too old"...! He doesn't know Beulah for the last 15 yrs like I do. It's a love affair really and now both of our hearts are broken. She does have 330K mi. on...

One of my TJM fogs has a broken housing. The plastic mounting boss on one side broke off. Probably been that way for a while. I can get a new fog kit from TJM for $130. I can’t just buy one or just a replacement housing from them. I believe all I need is Type C housing. I something like...

I have ordered a new IAC for my 97 LC with 290k miles. The existing IAC failed the test listed in the FSM; idle speed is sometimes poorly controlled. Will the computer have to learn the new IAC?

I’m picking up another 80 tomorrow and it’s rear bumper is cut to accommodate a trail gear. I much prefer the oem look, so will be going back to the stock bumper. Is there anywhere I can get a rear cross member? Does anyone on here have one or can point me in the right direction? Much love

I have LC Amazon 2002 (Diesel). i have driven since 2018, and it is in very good condition. Have had no major issues other than maintenance. Recently replaced "shocks absorbers" and all four globes since it was driving harshly. Since 2018, graduation test slowly reduced from around ten to...

I need a glass shop who can replace and seal the gasket on an 80 series correctly. The most recent opinion I have, which I don't trust given the source, is that the sealant that is specified in the FSM is no longer available and no replacement is available, therefore the repair cannot be...

Hi all, I recently had what I thought was a blown out master clutch cylinder. I ordered a new Aisin CMT012 from Rock Auto and installed it. I tightened it down and went to bleed it and noticed it was leaking terribly from the fitting. I took it back off and compared to the old MC and noticed...

Howdy all. Looking to replace the stock buckboard seats on my HJ45 pickup. Was looking at Scheel Mann and they said their seats have a thick backrest which may not give me enough legroom. I figure Recaros are the same. Any suggestions? I need a good seat for my lower back, so don't want...

Hi Guys and gals I don't post here much, spend most of My time in the 80 forum. I do DD a 2006 Tundra access Cab, it's a great truck and I really like it. It's been virtually trouble free during my ownership. It's a super clean low mile 125k truck. But it has leaky steering rack. it started...

Does anyone know if I can replace the base of this awesome antenna?

How often are you guys changing this out. I know it's a maintenance item but do you do it at 30k or what. I need to change the heater tees also. I guess do them both at the same time. and same intervals? Thanks,

1979 2F engine, D smogged, 91,000 miles, in the middle of replacing valve stem seals, and the replacement seals do not match the original seals on the engine. Been getting white smoke on start up that seems to reduce as temperature of engine reaches normal. More white smoke while driving down...

Forgive me as I have little electrical knowledge of these thing electrical wise. So, the inevitable finally happened on the trail and I forgot to lower my antenna on my 91 fj80. She snapped. I’m hoping the easy fix was that I could just take the mast off and replace it with a new one. However...

What does the MUD braintrust suggest for R134a valve core replacements and where to best buy them? I've just spent 10 minutes googling for Japanese/Denso replacement valve cores and the best thing I've found was questionable "Denso" valve cores from Ali-Express type website. I've just finished...

I have an ‘81 BJ42 with a 13B. I believe I need to replace the main bearings but I need guidance how to identify the main bearing specs for correct replacement as well as where to locate preferably OEM main bearing replacements. I don’t know the month or year of the engine. Here are some...

Hello all, currently in the process of servicing/sealing my front knuckles/axles and all that fun stuff on my 97 cruiser and came across my front driver side ABS speed sensor was partially broken and needs replacing. Any suggestions on where to get just the sensor and not the harness? or do i...

I finally started to tackle the wing window weatherstripping...figured 51 years so it's ok if I replace it a bit early. :) Well I managed to break the stud under the driver window...anyone know of a repair or replacement source? PS...I don't have a welder.

Never felt like I’ve been dragged through the mud like I was today…Remove and replace radiator along with upper and lower hoses. Radiator was cracked and it had to be done, but at what cost? Replaced with Denso 42302. Hoses replaced with Napa parts. The blows keep on coming —when I checked...

As stated, I have a 2003 HZJ78 with tired Dobinsons on a 2" (50mm) lift. I don't know what model or size the Dobinsons are. Looking for some suggestions for replacements options (ideal length, IMS vs remote reservoir, etc.). Maybe new versions of what I have are the best route, if I only knew...