I’m working on a 1995 Land Cruiser 80. The goal is to drop the sunroof assembly so I can weld up the roof rack holes (rack is already removed). I’ve already got the headliner out.
I was wondering if there was a way to drop the entire sunroof assembly as a complete unit and not remove the...
I m in the process of replacing the Pitman Arm & the Drag Link of my BJ 40.
I am unable to remove the 32 mm Nut that holds the Arm. Is it in the normal clockwise thread OR Counter clockwise thread ?
It is so tight & what is the best way to remove it. Not possible to heat due to possible...
I apologize in advance if this isn't the right way to ask a question. I haven't posted much on IH8Mud. I am starting a body off restoration of my 1970 FJ40. It is all original with a 3 on the Tree. Are there any good resources out there for videos or documentation on how to remove the shifter...
I designed and had fabricated the roof rack in the photo about 7 years ago for my ’92 80. At that time, I coated the finished rack with POR-15. It was starting to show some age and fading so I removed it a couple of weeks ago and had it stripped and powder coated which also matches the ladder...
I've taken the ABS stuff out except the harness and wheel sensors. I'm planning to send the wheel sensors to a mud member. I'd like to remove all of the associated harnesses - like the ones that run along the front suspension arms. If you've done this job, can you share any tips or tricks?
Hello I’ve read all the threads on the FRP Top removal and have gotten into the process enough to start scratching my head and wondering if my 1997 Colombian FZJ73 (Fives manufactured top) is secured differently than the JDM and European spec information and trucks that I’ve been using as my...
I recently replaced the shocks and coils on my LC 100 (220k miles), and also raised the torsion bars a bit. After doing so, I just found that both sides of my CV boots are leaking between the axle and the boot - the clamps aren't tight enough at the angle they're at. Both are leaking through on...
I did a search but couldn’t find a thread on this. Now I probably overlooked it and if I did I’m sorry.
I need to remove my window frame to replace it with a new one. I’m hoping I can losen the the FRP top enough to fold it out and put the new one in.
Anyone got a nice step by step to all the...
Does anyone out there have the silver bullet for removing a respray job and exposing the original paint? I am sure there are several nuances involved and I would love to hear about anyone’s successes or failures.
I have a green ‘74 that was resprayed at some point with a John Deere type green...
Hi all, I am trying to disassemble two 5687 winches to ship them, can anyone tell me how to remove the cable spool from the winch body? Do I have to open the case? Any help would be greatly appreciated!!!
Looking for help regarding my OEM PTO winch. I have recently purchased a 1983 BJ40. I am not overly familiar with the winch operation. Unfortunately, the winch is no longer operational due to a failure of the entire unit. The winch case has blown out along with its gears etc. It’s a bit of...
Hi all,
This is my first post as a 2013 LandCruiser 200 4.5diesel owner. I was terribly dissapointed by my previous car, a 2012 Land Rover Discovery 4 which had 3 catastrophic engine failures so I decided to switch to a more reliable car. This was the original idea.
After I bought the car in...
I tagged This question on to an old thread but did not get a response, so here is a separate thread.
’86 fj60 driver side (US Left rear) rear axle with semi float C Clip axle shaft that also has an ARB locker.
Need to remove the d/s rear axle, (US Left rear) does the fact that it has an ARB...
Anyone know the minimum I have to take off to get the timing belt off of the passenger side cams? I need to move some of the shims under the cams around on the passenger side but everything is put back together at the moment and not to do pointless work
07 VVT
Does anyone have experience with these Ramsey PTO boxes? It’s on a 1967 3 spd t case. I would like to remove and put the stock cover back in its place. I have a cover but not sure if it’s as simple as removing the bolts where the original cover was or do I need to split it open to remove a...
Starting to plan what kind of build to do on my new-to-me '14 LX. Bigger tires and sliders are first on the list. HOWEVER, I am also dealing with a garage built in the 1940s that is quite height restricted. I am looking at removing the roof rack since I likely won't need it for me and the dog...
I found this cool picture on here and wanted to know how these sensors/switches are removed? It looks like a ratchet or socket will turn them out, but wanted to make sure I don't damage anything in case I need to pull one out.
Thanks..