question

So, after quite a struggle, I've installed the new Warn winch and it works just fine. But then - the Cruiser won't start. All the lights, A/C, radio etc but not turning over. Check fuses. Can't find obvious problem. Passenger foot well fuse box pic attached. Engine bay fuse box pic attached...

1991 FJ80, a while back I had a shop who said they were experienced with Land Cruisers rebuild the front end -- axles, steering knuckles, maybe some other stuff, I don't remember. The axles they used were aftermarket, they have two outboard grooves for a snap ring, I suppose for different...

1991 FJ80 locking center diff only. 207K miles +/- when I got it, about 213K now. Very poorly maintained before I got it. Had a terrible whine on acceleration and a lot of clunking and banging on shifting and turning. Front and rear tires were different brands and the rear tires were far more...

Not a question specific to the 80 series but I want to add heated seats. I picked up a seat heater switch out of an 08 Camry that would blend in nicely and look factory but I am unsure how I would go about wiring it. My plan was to just get a heated seat kit and ditch the switches in favor of...

Can anyone provide the inner oval cutout dimensions for this aftermarket grill? I want to keep the radar cruise and want to see if there's any possibility of the Lexus logo cruise badge of fitting the height dimension.

Hello All, I have a question. I purchased a TRD SUPERCHARGER KIT with a 9th and 10th injector and TRD ECU My question is, will this work on my 2001 Landcruiser I've read several threads that my 2001 model only has a 9th injector, is it possible to add all 10? What happens if I can only add the...

Do I need to buy new clips? If so are they still available?

Hey! I'm looking to replace my OEM Torsion Bars, Rear Springs, and all four Shocks. My OEM torsion bars are so worn out that I'm sitting at stock height with them crank all the way down (up), and I don't want more than 1.5"-2" of lift in the front, and potentially 1"-1.5" in the rear. I was...

going thru boxes of parts and believe this to be a original pig dome light. single wire connector vs all threads ive found show two wire connector. thinking it came from a 69 or 70. not looking to get into another heated debate like the last dome light thread. just a simple yes or no will be...

There is a long bolt for the door hinges in a 1973 FJ40. Which is longer - top or bottom?

My current plan is to upgrade the suspension in a modest fashion. It is currently stock, but I want to match the springs to the load. I am planning to pull an overlanding trailer with tongue weight of 400#. However, that will not be full time. So how do I best compensate for this? The...

I ended up the the 97 HZJ 75 camper that was posted here recently. Needs some panel replacements, trying to track down an image of the below part numbers. Any help is appreciated, I was able to get a top panel from the place in NH and a window frame from Dubai.

Hi all, first time posting in the forum, visited a few times online but figured I’d register today, some very nice and interesting vehicles on here 😁. Hopefully I’ve picked the right spot to ask my question 👍 I’ve got a 1985 model BJ73 FRP top, has around 377xxx KM on the dash, 3B diesel which...

2000 LC. The headlights are terrible. The PO had LED's in the low beams and the spread was... Terrible. I tried the Hella 100W bulbs and - you guessed it - terrible. I have read a thousand posts, but have not found the answer. It's somewhat obvious that LEDs won't work well as low beams...

I have a set of H41 low-range gears taken out of a NOS split-case transfer. Never been on the road; I swapped in a Sumo gear set. The H41/transfer case combo was a diesel model, I was told, and these gears might thus be a slightly lower ratio than a petrol gear set, but I cannot confirm. I need...

When installing the Prinsu rack, I was hyperfocused on not allowing the bolt insert to fall into the headliner. I used silicone around the insert like the pics below., then pressed the Prinsu spacer on top of it. The seal is waterproof. What I didn't do, like the Prinsu Video mentioned, was...

Hi ya all here with other questions because I’m a cruiser newbie. Does this colter meter looks okay to you guys?

I am looking at purchasing a set of 16"wheels from City Racer (see link) to mount a set of 255/85/16's on - specifically BFG KO2's. My concern is the width of these wheels, even tho this is one of there recomended tire sizes. I like the idea of having OEM hub caps on my wheels which is the...

Has anyone installed a 5.7 gas Toyota V8 engine in an 80-Series?

A friend is helping me install a new axle, you think this shipping damage is acceptable to still install?