engine

Is anyone importing complete 1VD-FTE (single or twin turbo) engines for swaps? Is there a recommended source from which to import complete engines, perhaps from Japan, Australia, New Zealand, Tonga, Easter Island, or Liechtenstein? I want to replace the awesome, but old, frail, rare, and...

I've been hesitant to cut the LX engine covers but I'm often changing or exchanging the air filters. Wanted to pull together a thread to see how people might be cutting them for best function vs aesthetics. For those that may not know, it's pretty important to keep the section of the covers...

Got a cross member for an FJ60. I bought it to do a H55f conversion into a 62 and end up using an early mount and cross member. So this one not needed. $200 plus shipping.

Question for those more versed in F engines than I am. I was trying to get my 1973 started after a long restore. I finally got it to fire and was letting it run for 15 to 20 seconds at a time while I fine tuned it. Well, it seized up on me at one point. I discovered that my distributor was set...

Planning to do an engine swap on my J**p this winter. Wondering if someone has an engine hoist to loan. Willing to repay the loan with unskilled labor or random used 80 parts. Chris

If I want to check if my water temp gage is ready correct on my dash can I double check somehow? I have a direct temp laser could I shoot the engine block with that? What temp would you expect I should read after running engine

So the other day driving my LX home from work I had an issue. When driving, not accelerating or picking up speed, just a steady speed. The engine cuts out for 1/2 second to a second then runs fine. It did this 4 or 5 times during my 20 mile commute home. Happened at highway speed and around...

I'm looking for a cheap/free 2f engine. Im willing to rebuild one if needed. Something more local would be good. Thanks and happy trials!

Located in Beaufort sc engine is a L92, 124,000mi. Needs an intake manifold the one on it was damaged, finger is pointing at damage. Engine stand and hoist included $3000

Hey All, I just scooped up a '95 80 series this weekend out of Kentucky! The goal for this truck is to make it my daily in year when the lease is up on my Taco. Here's the details for the truck: 1995 FZJ80 - Moonglow Pearl 142,000mi low rust needs some fixin' So for step 1, I have to fix...

I had an old post that contained this, but other things as well (which are now resolved.) So, 1976 FJ40. Lights work. Start the engine and the headlights turn off (running side lights stay on). How in the world would that be happening? I've got a headlight switch replacement on the way...

Howdy all! Weather is getting cool here, and winter will soon be upon us. We get below freezing temperatures here and consistently in the 30s during winter. Is there a particular engine heater recommended for diesels like the H engine? I was looking at the Kat's Engine Heaters that heat up...

I have 2 batteries connected parallel for a 12 volt set up. I am told my batteries are bad. Since I need to replace them, what is the proper battery specifications for a 12th engine? Thank you

New owner of a 1995 Prado KZJ78W (Don’t know much about Cruisers) Question about a dim check engine light (can’t see during the day but at night it’s on and dim) upon ignition cycling the light is bright (how it should be if there was a engine problem) but after ignition it goes super dim. I...

Pulled this 1FZ-FE out of a 94 with an engine knock at 150k. PO blew a HG and had the engine rebuilt (poorly). Engine knock is occuring in cylinder 6 with very mild bearing wear but within OEM Spec. All other bearings checked out ok. I didn't spend a lot of time troubleshooting as I replaced...

Hello guys 2 days ago i crashed my beloved HZJ78 in a van on a extreme slippery road. No one got injured but the van is totaled and my land cruiser has some heavy deformation in the frame and the body. The body also has some rust so i think it is the time to buy a new vehicle. My land cruiser...

Good day one and all; I have a 1978 BJ40 with the 'B' engine which is shot. Has anyone been able to drop anything other then another 'B' without running into a lot of problems? Just wondering. Thanks, Don

It's this one-- Engine Skid Plate | 03-09 4Runner / GX 470 / FJ Cruiser - RCI Off Road - https://rcimetalworks.com/product/03-09-4runner-front-skid-plate/ 3/16 Steel, Black Powder Coat, Fairly new, No dings- $200

I've been seeing several places that will tune Toyotas including Land Cruisers. Has anyone had this done? The tuning is supposed to really improve the performance. I have a friend who had his Tacoma tuned and said the performance increase was dramatic.

I have an automatic transmission from my 1988 FJ62 with transfer case. Thee transmission got overheated so I swapped it with a replacement. Transfer case is solid. Make offer/any offer. Not willing to ship located in Long Beach Ca.