Search results for query: *

  • Users: jawjatek
  • Content: Threads
  • Order by date

Forum search Google search

  1. jawjatek

    Easy way to drain/change clutch fluid?

    I am wanting to replace the old filthy DOT3 fluid in my clutch cylinders. I was going to just install a whole new setup from JT Outfitters I just received, but wanted to try a fluid change and adjustment first, while I'm waiting on my flare nut wrench. 10mm, right? I found a used 10-12 mm...
  2. jawjatek

    UPDATED: FJ-60 misc parts for sale or free, 1987 model

    NO SHIPPING UNLESS INDICATED OTHERWISE - YOU PICK UP. FROM 1987 FJ-60 I don't want this stuff to go to recycler if any cruiser heads and headettes need it. 4-speed tranny GIVEN AWAY 2 Front seats, gray, GIVEN AWAY Spare tire hanger hardware. GIVEN AWAY Rear bumper, some rust, some dents, Dead...
  3. jawjatek

    Need hose fitting for AC compressor, or old comp for parts..

    This fitting on my AC compressor (the large one, LP side) has boogered threads. I need this fitting, and also the large hose.
  4. jawjatek

    mods delete please

    Never mind.
  5. jawjatek

    Quick AC evap rebuild question

    So after wiggling in my rebuilt evap unit under the dash, getting all the elec plugs reconnected, bolting it in, and putting the dash/ashtray/glovebox back together, I noticed a heater cable visible I wasn't sure was like that before. I'm probably being silly, because looking at it I don't think...
  6. jawjatek

    RTH needed: getting AC evap out... IT'S OUT

    Ok it is loose, 4 screws, the bottom bolt, and the 2 nuts are removed, the connector unplugged, the pipes disconnected, but I can't seem to get the thing back far enough to clear the firewall. Do I: 1. need to remove the lower heater duct? How? I took the one screw out and dropped it some, but...
  7. jawjatek

    Ugh. AC not blowing cold (again). Overhaul time.

    So I've been reading the FSM and every thread I can find (search does not work looking for "AC" only in the titles unfortunately), including Jen's recent AC posts. Looks like the system in my "87 FJ60 has already been converted to R134a because of the service fittings on the compressor, but the...
  8. jawjatek

    What winches fit the ARB 3410100 front bumper?

    Per the website they list the Warn 8274 and XD9000 and M8000. website: ARB Deluxe Bar Toyota Land Cruiser 60 Series 1980-89 (3410100) A recent report from mud member said he installed the Warn M8-s on this bumper and it included instructions for re-clocking the gearbox to run the winch...
  9. jawjatek

    Rear seat belt upgrade nut install

    I purchased the seatbeltplanet.com FJ60 rear retracting seat belt set to upgrade my 1987 FJ60 rear belts. The old lap retractors were old and jammed, and I want to be able to take along the whole fam on trips. Currently only 2 can ride with me, and one has to "ride bitch" using the rear center...
  10. jawjatek

    Yikes. Took off carb and found manifold issues...

    Yup, took off my carb to rebuild, and was going to install a trollhole carb in the meantime so as to stay mobile. I looked at the intake for the usual inspection, and yup, I think there is a hairline crack in my intake manifold, in the usual place. The crack is just a hairline, and I have not...
  11. jawjatek

    Looking for correct wiring schematic for USA FJ60 ignition with ignitor

    None of the FSMs I have from the usual suspects show anything on the wiring diagrams for the USA electronic ignition, they all show a points dissy. Anyone have the right one? I'd love to have a schematic that was correct for my 1987. In my 1987 FJ60, there are 3 connectors with one wire each...
  12. jawjatek

    Some more oil pan gasket questions...

    In the middle of a long weekend of odds 'n ends on my 1987 FJ60 2F USA cruiser. Today I took the leaky oil pan off - used the bottle jack and block of wood method. Very messy but had it off in an hour. Old gasket was cooked and hardened, but looks like at some point it was worked on, as there is...
  13. jawjatek

    Anyone using the trollhole distributor on a FJ60?

    I went to install mine on my FJ60 to use while the OEM is off to JimC for a recurve & rebuild. I didn't realize they did not come with a clamp so I am dead in the water until I get a clamp. :bang: Also after searching for info (which is hard to find) in that forum, I see the TH dissy is...
  14. jawjatek

    Side cover gasket: wet or dry? Goo or no?

    Hi y'all, nothing in the FAQ and search on the subject, and no info in the 2F FSM that I can see. Where is the side cover install procedure? Mine is off, cleaned up, and ready to go back on. Someone said 39 in*lbs on the screws... Do I use any FIPG or sealer on the Toyota stock gasket (cork I...
  15. jawjatek

    12HT diesel from Oz: Price check on aisle 4!

    I found a guy with a 12H-T drivetrain he imported from Oz: engine, trans, and t-case in a welded container. Less than 100k miles, he says. He is open to reasonable offers, but I have no idea what he has in it. He got it for a project vehicle, but is now selling the whole thing, plus a very...
  16. jawjatek

    Alternative manifold temp sensor for carb fan.

    Quick question: in my 60 that manifold temp sensor that controls the carb/manifold fan doesn't work. It is a short to ground all the time, so my fan runs for the full duration every time you turn it off. I think these are NLA (and usually so cooked on you'd have to cut it off), so I'm looking...
  17. jawjatek

    Wanted  need FJ60 2F exhaust head pipe in 30040 for "87

    Looking for a solid FJ60 2F engine exhaust down pipe, or head pipe. Start conv if you have one. Ok if EGR pipe cut off as long as main flanges are solid and crack-free. TIA
  18. jawjatek

    Anyone have an FJ60 2F exhaust pipe?

    Mine (1987 FJ60) is cracked so bad around the flange, I don't think it is weldable. Looking for one local or will call cruiserparts Mon. ACC can't help - already called.
  19. jawjatek

    deleted cat - temp sensor hole plug?

    Like the title reads, I deleted my catalytic converter while fixing my exhaust, so I unplugged and removed the cat temp sensor from the truck cat in one piece w/clamp and grommet, in case someone in a smog state needs it. Now I want to plug the resulting hole in the floor under the center...
  20. jawjatek

    Heat control valve issue fixing exhaust

    I am in the middle of fixing up my "87 FJ60 exhaust. As part of my work I removed the exhaust down pipe from the exhaust manifold. This led to the discovery that my heat control valve butterfly flapper has come completely off the shaft and is rattling around in there freely. The shaft has one...
Back
Top Bottom