Search results for query: *

  • Users: billy
  • Content: Threads
  • Order by date

Forum search Google search

  1. billy

    Can not find 37x12.50x15 tires

    I have 37 x12.50x15 goodyear mtr,s on my 40 they are wore out I need help . Any suggestions would be a great help . Thanks. Bill
  2. billy

    Fire extinguisher

    Fire extinguisher show us what you have and where you carry it in your 40
  3. billy

    Fairlead help

    Somewhere on this terrific site I saw a house fairlead for a winch line with no hook but I can not find it again can someone please help me out? It was a synthetic line that hooked on the fairlead. Thanks for your help and knowledge.
  4. billy

    Rear sill

    Witch rear sill does the 40 pros recommend real steel or ccot. I need to replace mine just wondering which one to chose . Do I need to replace both rear corners or just one , no rust in corners . Thanks
  5. billy

    help with tub differences

    i am looking at a april 1976 40. I have a couple of questions Are the posts behind seats smaller on an older tub? There is a bolt on lover on the right side of the tub above kick vent . Is this an older tub or aim I missing something ? thank for your help...
  6. billy

    charging problems

    1975 40 v8 2 wire gm alt .Is the white and blue wire the only supply wire to the whole system?
  7. billy

    usa vs import

    What is the biggest difference in a 1977 fj 40 that is imported vs a us model? is the gas fill hole not covered on an import ? It also does not have a heater . Will a 1978 hard top fit ? Sorry for all the questions just trying to learn if I should buy an import or not . Thanks for all the...
  8. billy

    white spokes

    ANY PICTURES OF 40 WITH WHITE SPOKE WHEELS AND 37 IN TIRES
  9. billy

    ARB air comp

    I have an older compressor on my 40 that just started leaking . Can anyone tell me if I can buy a rebuild kit or should I just buy a new one ? I only use it for 2 lockers Co2 for tires. Thanks for your knowledge...
  10. billy

    jackman white spokes

    Should I spend the money to redo a set of vintage 15 x 10 inch jackmans to replace a set of chrome spokes on a 40 with 37 inch goodyears ?
  11. billy

    Voltage drops to cab

    I HAVE INSTALLED A GM 130 AMP ALT THAT CHARGES CORRECTLY AT THE BATTERY BUT DOES NOT SUPPLY ENOUGH VOLTS TO RUN EDELBROCK FUEL ING AND HEADLIGHTS ? IT HAS 14.7 AT THE BATTERY BUT ONLY 11.5 AT THE FUEL INJECTION AND VOLT GAUGE. STOCK TOYOTA WIRING . THANKS...
  12. billy

    t 100 driveshaft

    one short Question for those of you in the know. Will a front drive shaft out of a newer model t 100 work for a c v shaft for a 40? I just saw one earler today and it looked like it would work (with a little modifing of corse)thought someone here would know. Can not seem to find older mini truck...
  13. billy

    Edelbrock fuel injection

    Just wondering what the experts think about Edelbrock vs GM throtle body on a 355 with a nv4500 ? Just trying to decide wich way to go . Thanks
  14. billy

    flat tires

    I have a sprung over 40 that will not fit in the garage at our new house with out letting the tire pressure down to 2psi. The question is will it hurt my 37 in. Goodyears to set with that little bit of air?It sure does look funny sitting that low again. Iplan on building a shop in the spring...
  15. billy

    new shop

    I am planing on building a new shop in the spring. About 30 ft deep 40 feet wide with 13 ft celing. Needs to be vinyl siding to be politicaly correct. what do you all think about block walls or stick frame? Also would like to put radiant heat in the floor but am concerned about putting in a lift...
  16. billy

    Holes in tub?

    I have a 75 40 that has 10 holes drilled in the tub above the rear tires and I can not figure out what they are for ! Any thoughts ?
  17. billy

    blowing engine fuse

    I have a 76 40 with a 250 chevy 6 cyl. just took it out for a cruise today after coming back from Tellico, and it just quit running down the road. the fuse to the engine was blown put in a new one and it blew right away. Hot wired it and got back home but I can not find out why it is blowing the...
  18. billy

    Death Wobble will not go away????

    I have a 1975 40 sprung over stock springs 4+ caster toe in 1/8 or out 1/8 shackel reversal Rock Logic steering Assist on a 16.5 to 1 saginaw steering box new tie rods and big ends 37 in. goodyear M T R's and can not stop it from doind the death wobble thing about 15 to 20 mph if you hit a...
  19. billy

    one more radiator ??

    What do you all think about an aluminum double pass cross flow radiator for a 40 vs std 4 core . I need a new radiator now . Going to install the 350 later just do not wont to buy 2 radiators. Thanks Billy
  20. billy

    steering assist question ?

    Just got a ram from Rock Logic came with #4 hose and fittings . Do you guys think that hose is big enough for the 1.5 ram or shoud I use #6 line ? I drilled & tapped my own box 16.1 sagnaw. Thanks...
Back
Top Bottom