Finally decided to throw some paint on the old girl. I ordered some Durabak smooth in green for the body and black for a bumper project I had going on at the same time. I know most of the forum posts that I found on the net didn't have very good reviews but I figured what the hell. So the...
I just moved to Germany and I'm looking for a Cruiser. Can anyone point me in the right direction? I've been looking through auto trader 24 and no luck so far. Where do I need to look?
i was checking for codes the other day and i pulled a code 42. the FSM says it a vehicle sensor. there is no page for troubleshooting. should i be concerned or looking for something? on a side not i'm slowly checking everything due to the lack of power while going up hill. i'm currently in lower...
the pulley for my a/c is squealing. when i turn on the a/c it goes away. i think the clutch might be on its way out. is there any way to test or diagnos it. i have the FSM but it does not cover troubleshooting. any thoughts ? thanks
what gauge wire are you guys using for a service wire? i tried some small stuff once, it burn't the :censor: out of my hand when i went to remove it. thanks
i recently noticed a new noise. it is coming from behind the tach area in the dash. i only hear it when the rpm's are above 1,000 and when i'm not pressing on the accelerator. it a beeee, low volume sound, that goes away as soon as i press on the accelerator. should i be concerned? i don't...
my 88' 62 was running just fine until one day last week the battery was dead when i went to start it. the battery is a yellow top and its been in there maybe a couple of years. i took the bat to advanced for a charge and test. charge and test good. i put it in yesterday at about 1:00pm. i go to...
i've serched the forum and found some different things to check out. i am hoping some one with a sharp eye can narrow my search for the problem. i just finished a OME heavy+ fr and rr lift. did a knuckle rebuild and rear bearings and seals. she sits a little bit higher in the rear. the pics are...
Q 1. does anyone have a pic or can tell me whats the right way to install the anti-rattle clip ( which side goes towards the disc). the FSM isn't real clear and its been a while.
Q 2. where can i get an extended brake line for a 88' 62?
what kind of paint can you use for the inside of the knuckles? i'm doing a rebuild and the paint was gone and replced by rust. so now after sandblasting the knuckles (along with other suspenion parts) i was qurious if it requires some sort of special paint or if good ole-semi black over primer...
ok, what started out as a OME heavy plus front and rear lift, a knuckle rebuild and a rear end rebuild, has become a suspension overhaul + paint. everything has been taken appart and now my truck is sitting on jack stands. theres a guy not to far from me that does beed blast and powder coat...
i'm in the middle of a Lift/knuckle rebuilt. i can not get the cone washers out of the top of the knuckle:mad::mad::bang:. i've used pb blaster, wd 40, hammer and drift, screwdriver. what do i need to do?
i would like to send out a request for some dimensions. if you gentlemen could help me it would be much appreciated. i'm looking to get the dimensions for the old style arb w/ bullbar. the thickness of the metal, size of the tubing, lenth, width, depth etc. i am planning on building my own...
i'm getting ready to do a knuckle rebuilt and replacing the inner seals. thinking about going the synthetic route in my diff's and tc. for the guys that run synthetic in there diff's and tc what are you putting in there and have you noticed a difference (more power, better fuel economy, etc.)...
i'm going to lift my 62 with a 3'' ome heavy, i looking to tuck 33x10.5x15's under it. my question is with an a440 tranny do i need to regear? keep i mind its a dd and i'm going in the expedition direction.