Maybe a little rougher but it's nothing crazy.. I'm sure comfort mode would mitigate what little change there is.
LX 600 Aftermarket Wheel Choices (2 Viewers)
- Thread starter ElvezTX
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
They look good. Have you checked for rubbing on the UCA at full lock? I had those same tires and they rubbed the UCA at full turn.
None that I can feel or see.. I keep the suspension in H1.
JAOS TRIBECROSS 20x9.0J 55 6H139.7 TITANIUM GOLD WHEEL B952090TGD
Nokian Outpost nAT 275/60R20 115H
At normal height and max turn Ican put index finger between uca and tire.
Should i ran stock pressure 33psi?
Nokian Outpost nAT 275/60R20 115H
At normal height and max turn Ican put index finger between uca and tire.
Should i ran stock pressure 33psi?
If the Nokian's are rated as an LT (Light truck) tire, then I would expect around 40psig is the target inflation pressure.
For example my BFG KO2 require about 41-42psig to be properly inflated for the same load carrying capability as the factory "passenger" tire.
There were 2 choices for nokian outpost nat in this size i have installed one with lower load rating and weight
Speed Rating: H (130 mph)
Max Load: 2679 lbs
Max psi: 51 psi
Weight 46.3 lb
Vs
Lt one
Speed Rating: S (112 mph)
Max Load: 3417 lbs
Max psi: 80 psi
Weight 52.9lb
In this case, you're probably good at the OEM inflation pressure.
Those look awesome. Love those JAOS rims. Nice to see 34's fitting! I'm going to try Falken Wildpeak AT4 in 285/70R18 (34") too once they're available.
FWIW, I use this site for tire pressure recommendations. It's saying you could run as low as 26psi (if I put all the info in correctly) based on load rating but I wouldn't go below 33psi.
Tire Pressure Calculator
Easy to use tire pressure calculator. Use our tire pressure calculator to calculate the new tire pressure needed when changing tire sizes.
Yes tire pressure sizing in calc all correct numbers. I will set at 33. Shop did 36 and it seemed a bit firm but not as firm as e rated ko2 at same pressure. As far as diameter please note p rated is 33 inch tire whereas e rated is 34! In the same size! Apparently e rated has deeper thread according to spec. I can confirm that p rated 275/60/20 on 55 offset fits with around 10-15mm distance to ucaThose look awesome. Love those JAOS rims. Nice to see 34's fitting! I'm going to try Falken Wildpeak AT4 in 285/70R18 (34") too once they're available.
FWIW, I use this site for tire pressure recommendations. It's saying you could run as low as 26psi (if I put all the info in correctly) based on load rating but I wouldn't go below 33psi.
Tire Pressure Calculator
Easy to use tire pressure calculator. Use our tire pressure calculator to calculate the new tire pressure needed when changing tire sizes.tiresize.com
View attachment 3540227
Those are not but they use a shallower tread depth compared to the other NON OE and AT4. They are very light though, like 37-38lbs which is perfect.
I called Sumitomo and got all the specs. They were built specifically for Toyota OE use.
The next one to look at would be to the Yokohama in that size but it weighs like 46 or 47 lbs.
Great looking wheels and thank you for the tip!. I just bought the same sets and my dealer is telling me that the OEM rug does not fit (too large). What did you use and what were the dimensions? Thank you!
Just to be clear, I got the JAOS wheels
These look great! My Lexus dealer is hard time installing these jaos wheels since the OEM rug nets are too big to fit. What did you use for yours and where did you find them? Appreciate the advice!
I bought mcgard 1.5x14 spline drive lig nuts. Yes oem nuts are different they are flat while aftermarket wheels need conical seat. I picked black ones and they look great. McGard 65515BK Black Spline Drive 5 Lug Wheel Installation Kit (M14 x 1.5), 16 Lug Nuts / 4 Locks / 1 Key / 1 Install Tool https://a.co/d/4fovS8Xhttps://a.co/d/4fovS8X
Thank you so much for the fast response! Just ordered these!
Get some extra. 6x4 =24. You can find a separate set of 4 lugs. Also LX600 wrench is 21mm (lc200 wrench is 22mm) and spline drive for aftermarket lugs is also 22mm(I used one from lc200). If you carry extra oem lugs for spare OEM tire you can get combo wrench and keep it in the wall next to jack. EPAuto Telescoping Lug Wrench, Wheel Wrench with CR-V Sockets (17/19, 21/22mm) https://a.co/d/dEwhBI3
Last edited:
Have people in the Middle East found a way to make the LX600 less ugly, do they just use ARB bumpers?
We don't view it as ugly as you guys do.
The GX 460 now that is ugly.
It could be better, yes. However, when its such a common vehicle and have been seeing it in large numbers daily for almost 10 years with a big grille (since 2016 update debut in end of 2015) that it doesn't seem offensive to us.
xeuxaz
SILVER Star
The 460 is definitely less attractive. No split tail gate on the 600 is the kick to the balls.
If anyone is interested I have the Vossen HF6-4s 30 that I purchased from ElvezTX in the beginning of this thread. I ended up never mounting them and have since sold my LX600. They are taking up room in my garage and would give a sweet deal to anyone that would be interested in them. I have everything, including, lugs, and TPMS.
