Elbee

Been doing some bondo here and there where I used a stud welder to pull out some dents the troopy had, the circles in the metal thats left behind would look noticably bad. Also bondo'd some of the wheel well that I rewelded as it was quite wobbly...

Bumping the old thread as this may help out. I found a still available Denso fuel pump ( 951-0020 ) that worked for my '01 LX470. Looking at the Toyota parts diagram part numbers, looks like the base model 2nd gen Tundras that came with the 4.7...

A little wet sand and re-clear it. Most clear failure is due to neglect and the driers from car washes. If people would just wax it a few times a year… Even the fj cruiser with its notorious clear coat issues can be mitigated/prevented by good...

Alright, I made like 0 progress today 😂 Spent a couple of hours masking/taping-off weather stripping here and there. Then I laid down some more paint on one of the doors, and it just came out like absolute sh!t. Horrible. I was not pleased...

Kubota came in two oranges, an early and late I believe. The earlier being more red than the later bang orange. I have noted that the U.S. market did not seem to get the toyota /kubota bang orange that oz got much. May be worth checking the...

If you cleared over it, that would prevent it from fading and going chalky, correct?

Alright well, my air compressor decided to eat its belt, which I inspected prior and it looked totally fine. Halted my progress immediately, so I tried to make this negative thing into some sort of positive bit. Organized a bunch of crap, cleaned...

Bump! 👊 A/C got fully gone through. New compressor, new lines, new drier and conedesor. The A/C blows cold 🥶 🧊 One of the most sorted out mechanically 75 series troopys out there and one of the lower miles ones as well.

I have one but’s it’s a split one. I’ll take a photo

Super clean 2008 Toyota Land Cruiser VIN JTMHY05J284000860 Garage kept 163k miles No accidents BBS Forged TRD Heritage wheels Spydertrax spacers (5) BFG KO2 Icon suspension Baja Designs LED light bar TRD shift knob TRD red start button Switchback...

I’m a fan of the OE rims. The 16” ones on the early 100s in particular are functional and so cheap they’re practically disposable, but they don’t need to look that way. I scored some on FBM for next to nothing, but they were covered in...

The female thinks this truck is hers….

I actually told him to not contact me again! Just the engine alone is worth between 10 and 15K , good luck finding a good one with low mileage.

Can you guys believe that someone actually tried "lowballing" me with an offer of 18K, WHAT THE F..K !!! I need to take a walk and calm down!

The water pump and all wheel bearings were replaced 2 years ago. The steering box was rebuild in Texas 6 years ago. New Ti-rods 5 years ago. Sound proofing was laid all over floor a few years ago.

I bought the cruiser in Sacramento Ca. 12 years ago. The conversion was done 10 1/2years ago. I've put around 50k miles on it. The donor vehicle had 375,264 kilometers at the time around 233,178 miles. Why selling this Beauty ? I'm going on...

California Cruiser with 315,000.miles in very good condition. $25,000. 12Ht TurboDiesel with 287,000 miles From a 1988 HJ61 5 speed transmission Full floating axle rebuilt 3 years ago. 4:11 Newer suspension 2" Toughdog. New Wheels with new BF...

Here's one of the top, and one of the bottom,

Hey all, I posted this storage panel I made on the What have you done to your 100 thread, and some people asked for the file, so I've uploaded it to MakerWorld. Here's the link - MakerWorld Land Cruiser 100 Center console storage panel I...

Great explanation on Australian UHF. I’ve used HF extensively in east Africa and Middle East. We mount our aerials on the bull bar almost exclusively with two special trucks mounted on the side or rear due how they came to us. The front mount...

Yeah, to echo what @mudgudgeon said, UHF is the standard way people do vehicle to vehicle comms in Australia these days. Mounting on the front of the vehicle like that is preferred. If you try and mount off the back of the vehicle next to a...

Bundaberg Rum stickers RM Williams stickers CU in the NT stickers Shoot Ferals stickers . . .

Sorry for the delay in response. I did. It was the master cylinder. I typically start with the lowest cost culprit and work my way up from there. I replaced the slave cylinder and it didnt fix it. Replaced the master and its good as new.