huminajumina

C1 Blue connector pin 35 is the CPP wire (clutch pedal position) the switch just interrupts ground. The diagrams I’ve been using are here LT1swap

In the winter I need to leave the choke on (at least a little) for a long while due to the header. The fluid heat riser does help but the engine needs to have some heat in the coolant to work.

Maybe I'll quit being a dumbass and try driving without the choke closed. Seems to run better that way. Jeeeeezzz.

Last weekend I saw about a dozen lifted trucks with the LED light rings around the wheels, little tiny tires, and big ass rims. My wife was laughing her ass off, asking why the hell they even have trucks, it's obvious they never get used for...

Anyone know if these will fit without cutting my quarters?

Drove through the bitterroot last Sunday- no smoke. Did a mtn ride down in Sula, lots of fun. Guess I got lucky. Cruiser Content- spotted four ‘40’s between Missoula and Salmon. Bitterroot never r disappoints. The one in Salmon had some sweet...

The whole dang valley smells like a campfire now, smoke blowing across the valley floor, smoke in the mountains. Summer smoke season arrived.

Montana sucks ~ @rkymtnflyfisher allegedly

Kitty 's gotta eat...

We had a great dinner, Shannon made quesadillas, then the rain showed up and we hung out in the tent, here is a picture of Charlie passed out while I finished an adult beverage or two and watched the lightning show. The amber color of that photo...

This weekend was great, I got to put the cruiser through its first test. We loaded up and drove it right back to where I was in April when the crankshaft snapped. We loaded up for a quick one night trip, and drove out to the mountains to take...

Yes it’s good to be putting some miles on and enjoying it. Yes the PO installed steel caster shims while the shackles were installed.

Glad to see you enjoying the swap! if you don’t have caster shims in with those long front shackles, I’d highly recommend some.

I've put about 200-250 miles on the swap so far and things are great. A/C is cool, the engine is running great. Today we went to a few appointments and ran some errands and the cruiser did great. We stopped by Cruiser Heaven in Hagerstown (since...

Well those knock sensors fixed it. Both Knock sensor codes are gone, so I am happy with that. The new O2 sensors are installed, I am not sure they really changed anything, but Its probably best to have a matched set and new ones should work well...

Haha, that 40 is looking good!

I’m around. But maybe you missed me because I have been driving my 40 a bit more lately!

Dude! Perfect! Yes that’s exactly what I need.

Time is once again scarce, I just got back from a work trip that turned into two trips…. Unfortunately I was stuck in Hawaii for 10days …rough life. Didn’t see @Aloha Jen & her 60 cruising around anywhere 🤷🏻‍♂️. I was able to come home for...

My Saginaw box is mounted out front, I REALLY like the way your steering gear box is mounted in the engine compartment. Had I more youthful motivation and energy, I would do something along this line. On the other hand, @Jdc1 absolutely...

Al- you are going to make me blush.

Thanks guys, I appreciate the input, glad I'm not alone. I know the directions were oddly specific and vague enough to give me a good starting point as I bolted it together....The pedal feel, travel, and function. (friction point) all feel good...

Great work duder. Yep, same noise on mine. Idk how well I adjusted my bearing to be honest, it's been working fine for this long so it's on the back burner currently.

Great job man! You made quick work of that LS swap. My throw out bearing makes the same noise, I think I need to adjust the collar on the marks adapter out some more so there’s constant pressure on it. My exhaust is also run underneath the...

I took the wife and dog on a quick ice cream trip last night. So far so good: • the A/C is running good for now, I’ll keep an eye on it. • The throw out bearing is making a little noise when engaging the clutch pedal, but it feels correct. I...