I always go spare to LF... I figure the front is the hardest on tires, where they wear the most.. so make the guy who just got off break go up and do some work. Then 5 rotations later he comes of the RR and can go on break again. probably...
Ok here's a new one. dashboard accessory mount, fits 77 and newer using the screws for the defroster vents.
My 40 has carplay now... the sound comes out of a bluetooth speaker that rests on the tranny hump
videos, more pics, all...
hey Brian, thanks so much for the kind words and so glad you're happy with everything! Can't wait to see it all mounted up...
and Ken, best part of our story is we've been friends since before I even made my first rack. so grateful for...
Good afternoon folks
I post some on the 80 series. (not enough) But owning a 200, as well, 2 of them the wife drives a18 and mine is a 21, I lost my 14 to one of Bambi’s relatives. (R.I.P) And replaced it with the 21,
A shout out to Gamiviti...
Hey Geoff quick question... I recently had to get a new phone (old one lost its cellular network connection) and I have a new phone now, another iPhone 15. I have done all sorts of restores from backup, etc. but for some reason the Toyota...
yes. we sell a cross bar kit to add extrusion cross bars across the top of your OEM rails. Can be done in any length, I think that's what you're after? Our wing brackets are a direct bolt-up, here's a pic:
hey @Beastiethe70 ! great to meet you in line up before the photo!!! so many cool 70 series.
Of course, I could repeat the glowing descriptions of this area, the awesome people, the chill welcoming vibe...it was just plain great!!!!
I gotta...
Hey SAS gang! the lovely @Mesa Woman reminded me that I should probably post up a reminder... remember tomorrow night (Thursday) we'll be doing a little whiskey tasting, over by the main event area... say 7:00? top three answers...
1...
Update:
The following codes were found. P0729 Gear 6 Incorrect Ratio, and P2714 Pressure control Solenoid “D” Performance or stuck off.
Slee got the truck in and pulled a sample of the transmission fluid. They said there were metal specks in...
@riffman12 Good timing- we just released a new version of our roof channel towers called the "shorty" version... the height difference is 1.25" compared to the standard ones. So per the technical term above they now come in "pretty dang low"...
I could get pics and measurements of that setup off a sequoia if that helps. I know...it's a long shot but if it helps...
and I have my gamiviti rack and towers pretty dang low. I can measure in a day or two (traveling right now)
does anyone have 3 of the cross bars on a 100 series that can speak to the height of them off the roof? I had the Eezi Awn K9 roof bars on my last cruiser but would love if I had something that sat a bit lower.
I'll be mounting an Autohome roof...
Hey Jim, remind me I'm tossing a handful of square end caps into my glove compartment... we can dress up that Jerry can holder next week.
also thanks again for the help with the voltage regulator swap! always good to get the 82's together...
Can confirm that the center tower bolts are the weakest point of the OE rack design. They sit in a little well that fills up with water, so the torx bolt heads sit immersed most of the time. There should be a better drainage means in that well...
Hey guys! October is right around the corner and registration for new COTR5 drivers is officially set to open Saturday August 2, 12pm EDT at cruisersontherocks.com. Early registration for past COTR attendees plus Cruisers on the Rockies attendees...
It wouldn't really be possible to put a 200 series rack on a 100- aside from the length/width differences, the bolt spacing on the 200 is a lot narrower, so the holes just wouldn't line up.
Also your concern about the missing cover and water is...
I'm back in business. Picked up the 74 at Cruiser Outfitters this morning. It is an amazing transformation. Kurt's crew did an outstanding job. Now I can confidently bring it and pull the Kimberley.