What Did You Do with Your 80 This Weekend? (48 Viewers)

[RFB]

Got this from @wits-end tube is 3/8"
Air Coupler Bracket- guarded KIT

Yea I have those fore and aft as well I was asking about the frame in rear where sliders are. I got my answer thanks looks awesome.

 

[RFB]

Installed walker direct fit. Last piece of the muffler puzzle. Haven't pulled off the lift yet, but it idles nicely hopefully no more cruiser whistle

View attachment 1840962

View attachment 1840963

Double cardon in the rear? What type of lift you running??

 

[Sanchez]

Yea I have those fore and aft as well I was asking about the frame in rear where sliders are. I got my answer thanks looks awesome.

ha my bad, i quoted the wrong person and message. cheers!

 

[RFB]

ha my bad, i quoted the wrong person and message. cheers!

not a prob how much hair did you lose putting in new rug, I have it just dont have the patience to install. plus its always freezing here

 

[Jgrauman]

Double cardon in the rear? What type of lift you running??

4" lift. PO installed custom DC front and back. I am in the process of looking for a stock shaft to replace it. The pinion angle needs to be moved much further up to run the DC and I don't want to do adjustable UCAs to correct, I don't want the spring perch pushed that far back. I have been in limbo on UCA's or stock shaft. I have vibes right now when letting off the gas. I just don't want to go stock DS and still need to adjust the pinion. It appears he also put longer LCA's they look like slee HD so the pinion is sitting parallel by my eye, I haven't measured. I think the driveline shop just sold him on DC as a fix all.

 

[RFB]

my bad, thanks

 

[Sanchez]

What wire sizes are in that harness, there's ZERO AWG information on the sites I found related to that product.
I suppose you could just use 2-3 conductors to 'build' a larger wire but...

According to the other instruction page on the site, the wires are 8ga. I'll find out and let you know. I was also thinking of using more than one conductor if needed, comes with 12-14 can't remember.

 

[Lost Industries]

looks good, where did you get the slide out tray from ?

I built it myself. I have a machine shop/fabrication shop. I sourced the slides and then drew up and bent the tray out of aluminum. My thought was to make a kit with the bolt in frame and then different tray options.

 

[Dissent]

According to the other instruction page on the site, the wires are 8ga. I'll find out and let you know. I was also thinking of using more than one conductor if needed, comes with 12-14 can't remember.

Thanks. Those can't be 8 AWG given there's like 20 of them going through a 3/4" hole. The majority look like about 14 AWG.

 

[Stuckinthe80s]

Pulled off a 4 night route with the family thru some amazing terrain. About a 200 mile dirt loop with the little kids outnumbering the adults! Cold but no wind. Fairly desolate with exception of Alabama and Warm Springs. Plenty of crying, cuts, bruises, but they had a blast playing! A success in my book. 80 did great, no issues, but no news there haha.View attachment 18406941st night gathering.View attachment 1840701 Got above and away from the smoke.View attachment 1840695 Cooking dinner and kids playing.View attachment 1840700 Fun ahead!View attachment 1840698Sunset and water freezing in 3-2-1!

Very nice! How are you liking the iKamper? I've been doing a lot of reading on them and I think that may be my next big purchase.

 

[pawnthatdude]

Pulled off a 4 night route with the family thru some amazing terrain. About a 200 mile dirt loop with the little kids outnumbering the adults! Cold but no wind. Fairly desolate with exception of Alabama and Warm Springs. Plenty of crying, cuts, bruises, but they had a blast playing! A success in my book. 80 did great, no issues, but no news there haha.

I was the other 80 series you saw on Steele Pass road. Good to see you guys out there, looks like you had fun.

 

[ExpoGeorgia]

Drove to the beach

 

[baldilocks]

Installed my @yodaTEQ beer holder!
View attachment 1841453
Thanks to Frank at @yodaTEQ for hooking me up with the parts! Now I have more wiring to do!
He showed me a new place to get tacos too.
View attachment 1841454

They work great as an antenna mounting location too. Yes, Frank was a pleasure to deal with. I am very impressed with the quality and precision of his beer/antenna bracket.

 

[Fj81]

View attachment 1841849
They work great as an antenna mounting location too. Yes, Frank was a pleasure to deal with. I am very impressed with the quality and precision of his beer/antenna bracket.

They look good!

 

[davidp14]

Front main seal, oil pump gasket and screws, and new fan, clutch, and belts. And some paint on the cover too.

 

[RFB]

Fixed my deathly slow power windows using @SUMMIT CRUISERS write up “got slow windows” best mod in a while cost nothing except maybe some dynamite replacement

 

[Box Rocket]

Front main seal, oil pump gasket and screws, and new fan, clutch, and belts. And some paint on the cover too.
View attachment 1842027
View attachment 1842028

I'll be tackling this same job over the next couple weeks.

 

[davidp14]

I'll be tackling this same job over the next couple weeks.

It really wasn't too bad. I posted about it in my build but you really just need to follow the you tube video that Texasknowhow made.
I Finished it in less than 6 hours .

 

[RFB]

It really wasn't too bad. I posted about it in my build but you really just need to follow the you tube video that Texasknowhow made.
I Finished it in less than 6 hours .

yup

 

[RFB]

Front main seal, oil pump gasket and screws, and new fan, clutch, and belts. And some paint on the cover too.
View attachment 1842027
View attachment 1842028

Did you tie 3/4 breaker bar under frame and BUMP, @OTRAMM hates when people do that but everyone isnt as fancy as ryan Lol