Parting an 80 series in SoCal TLCA members preferred.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Status
Not open for further replies.
Deathvalleypaul

Deathvalleypaul

FJ80 Collector
10 Year
Joined
Apr 25, 2011
Threads
907
Messages
3,832
Location
Near Pasadena CA
1996, Very Complete with title, but smog and tags overdue. Minus Headlights and Valance. Minus visors.

Message for parts, or whole car. Shipping possible on small parts. U remove other parts.

REAL NICE SET OF 4 WHEELS AND 5 TIRES ALSO AVAILABLE 275/70/16 factory wheels in great condition, tires have good tread all terrain, wide footprint, not noisy.

I am near the 10 freeway and Rosemead, TLCA members
Prices are $10 to $4500 for parts.
 
Deathvalleypaul said:
1996, Very Complete with title, but smog and tags overdue. Minus Headlights and Valance. Minus visors.

Message for parts, or whole car. Shipping possible on small parts. U remove other parts.

REAL NICE SET OF 4 WHEELS AND 5 TIRES ALSO AVAILABLE 275/70/16 factory wheels in great condition, tires have good tread all terrain, wide footprint, not noisy.

I am near the 10 freeway and Rosemead, TLCA members
Prices are $10 to $4500 for parts.
Click to expand...
Out of curiosity is the vehicle running? If not what was the issue?
 
runs good. just expired tags and a noise in the engine, some minor body damage to quarter panels , torn front seats. I was going to restore it, but don't have the energy or time any longer.
 
8250
The locker axles and ECU are worth $5000 alone.
 
If still parting, could use the strike plates for the rear jump seats.

Frank
 
Hi Frank, They are grey and in good condition. The buttons are not included; all of them fall off. You can buy new buttons on line and GLUE them down when you put them on and they will last. The pair of steps will run you $40. I can ship them for $12.62 The steps are in good condition. I can get a pair of used buttons for you for $8.
Paypal to Deathvalleypaul@yahoo.com Please pay as a gift and note: Congrats on Next Step!
 
Deathvalleypaul said:
Hi Frank, They are grey and in good condition. The buttons are not included; all of them fall off. You can buy new buttons on line and GLUE them down when you put them on and they will last. The pair of steps will run you $40. I can ship them for $12.62 The steps are in good condition. I can get a pair of used buttons for you for $8.
Paypal to Deathvalleypaul@yahoo.com Please pay as a gift and note: Congrats on Next Step!
Click to expand...
Just to make sure, am looking for these...
 
Strike plates

20220827_145427.webp
 
Handles wouldn't hurt too.
 
Is it just the pair of strike plates, one for each seat; total two? Do you mean the fabric handles that are on the 3rd row seats? I have at least two of the strike plates.
 
Perfect. I need 2 plates, will get all 4 if you have them. I am installing jump seats in a 60 so could use the handles if you have them.
 
Please see your personal message.
 
Thanks. It hasn't posted yet but I'll keep an eye out for it.

Frank
 
@Deathvalleypaul
Do you have the driver side body harness, rear crossover section and rear locker harness available? Converting an unlocked truck to Locked the Toyota way.
 
On that gray interior, do you have the rear tailgate carpet?

Frank
 
offr0adlim0 said:
@Deathvalleypaul
Do you have the driver side body harness, rear crossover section and rear locker harness available? Converting an unlocked truck to Locked the Toyota way.
Click to expand...
Sold the full haness set with rhe axles. Why not use an after market harness..
It not only simplifies insulation, skips ECU, and best of all allows u to use front locker without having to engage the rear locker. Factory only allows you to use front when rear is engaged.
 
Deathvalleypaul said:
Sold the full haness set with rhe axles. Why not use an after market harness..
It not only simplifies insulation, skips ECU, and best of all allows u to use front locker without having to engage the rear locker. Factory only allows you to use front when rear is engaged.
Click to expand...

It’s a build for a client and aftermarket is not an option. I have already sourced an ECU. Looks like I will be adding wires/connectors to his body harness.
 
Status
Not open for further replies.

Share this page

Back
Top Bottom