Hey all,
I'm officially no longer gauging interest and am instead selling them!
What they are: (4) ip68 water resistant, 10 led lights (6 led lights are available instead of 10 if you want something a little less bright). (4) hand made (to keep price down) stainless steel protective brackets to mount each light to the frame. (2) wiring harnesses, one for each side, which are pre soldered with connectors to connect to the factory runningboard light socket.
The full kit will work with any LX or LC that has, or had, the AHC system and lights on the running boards. Theses will work if you have sliders or running boards currently installed.
The AHC system does not still need to be in place to mount these. The 2 bottom bolts that held each of the 4 accumulators on will be needed though (I can provide those if needed).
The light can be switched on when driving to act as rock lights very easily!
First remove the kick pad but prying/pulling up on it:
Then you expose a small black plastic screw. Unscrew it.
Now remove the side panel by gently pulling on the front (closest to the firewall) till the tabs pop loose, then sliding the panel back to remove it.
Now remove the door jam plate and gently pull up on the carpet as seen.
Under the carpet, you will see the rubber boot and two wires from the factory connector. You will have to tap into these wires using wire taps. I usually solder most my wires but given the proximity to the carpet, I used taps to avoid burning anything.
To wire a non led indicated switch, you only need to tap into the ground wire (red with blue stripe). To wire a switch that has an LED indicator, you'll need to tap both the ground and power wires. Since this is a ground switch as opposed to a traditional power switch, finding an LED indicated switch that will work properly was tough. For that reason, I won't be including a switch with the setup. The only led indicated switch I could find that would work was a 4 pole cheap switch from amazon: E Support Car Marine Blue LED Toggle Switch Dash 4pin Pack of 5 Amazon.com: E Support Car Marine Blue LED Toggle Switch Dash 4pin Pack of 5: Automotive
Here is an example of the switch working:
Here are the purchase configurations:
1) Full plug and play kit (check your connectors for corrosion)
If you would like a wire taps, extra wire, and all the nessessary crimp connectors to make them work as rock lights please request it (you will need to supply your own switch and have the ability to crimp the connectors).
Price: $135 plug and play +$10 for rock kit
2) Full kit minus the connectors (good for if your connectors are too corroded and you need to hardwire; will include crimp connectors on ends but can be cut off if soldering.)
Price: $130
3) just the 4 brackets for use with own lights and wiring.
Price: $70
All prices include ups ground shipping. If local pickup, $15 shipping is waved
So here is one of the brackets
Here's it is mounted to the truck
Here is one completed side. You would receive two of what's pictured and 6 small zip ties for the wiring between each light. All the wiring is soldered, heat shrinked and covered with a loom.
I'm officially no longer gauging interest and am instead selling them!
What they are: (4) ip68 water resistant, 10 led lights (6 led lights are available instead of 10 if you want something a little less bright). (4) hand made (to keep price down) stainless steel protective brackets to mount each light to the frame. (2) wiring harnesses, one for each side, which are pre soldered with connectors to connect to the factory runningboard light socket.
The full kit will work with any LX or LC that has, or had, the AHC system and lights on the running boards. Theses will work if you have sliders or running boards currently installed.
The AHC system does not still need to be in place to mount these. The 2 bottom bolts that held each of the 4 accumulators on will be needed though (I can provide those if needed).
The light can be switched on when driving to act as rock lights very easily!
First remove the kick pad but prying/pulling up on it:
Then you expose a small black plastic screw. Unscrew it.
Now remove the side panel by gently pulling on the front (closest to the firewall) till the tabs pop loose, then sliding the panel back to remove it.
Now remove the door jam plate and gently pull up on the carpet as seen.
Under the carpet, you will see the rubber boot and two wires from the factory connector. You will have to tap into these wires using wire taps. I usually solder most my wires but given the proximity to the carpet, I used taps to avoid burning anything.
To wire a non led indicated switch, you only need to tap into the ground wire (red with blue stripe). To wire a switch that has an LED indicator, you'll need to tap both the ground and power wires. Since this is a ground switch as opposed to a traditional power switch, finding an LED indicated switch that will work properly was tough. For that reason, I won't be including a switch with the setup. The only led indicated switch I could find that would work was a 4 pole cheap switch from amazon: E Support Car Marine Blue LED Toggle Switch Dash 4pin Pack of 5 Amazon.com: E Support Car Marine Blue LED Toggle Switch Dash 4pin Pack of 5: Automotive
Here is an example of the switch working:
Here are the purchase configurations:
1) Full plug and play kit (check your connectors for corrosion)
If you would like a wire taps, extra wire, and all the nessessary crimp connectors to make them work as rock lights please request it (you will need to supply your own switch and have the ability to crimp the connectors).
Price: $135 plug and play +$10 for rock kit
2) Full kit minus the connectors (good for if your connectors are too corroded and you need to hardwire; will include crimp connectors on ends but can be cut off if soldering.)
Price: $130
3) just the 4 brackets for use with own lights and wiring.
Price: $70
All prices include ups ground shipping. If local pickup, $15 shipping is waved
So here is one of the brackets
Here's it is mounted to the truck
Here is one completed side. You would receive two of what's pictured and 6 small zip ties for the wiring between each light. All the wiring is soldered, heat shrinked and covered with a loom.
Last edited:
