Latest recommendation on phone mount? (5 Viewers)

[kiedistv]

I use a mag quadlock wireless charging head mounted to one of those panels that replace the grill. Works really good for me.

Apologies about the messy car and the homemade ashtray.

 

[Skiime]

Been using this one for a while now. I ran the usb-c cable to the fuse box through the vent, so you don't even see it when the phone is mounted. The adhesive is surprisingly strong. It's been working great for years now. The magnet is very strong as well...never had any issues with the phone falling off.

https://www.amazon.com/dp/B09QPN1TNV?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_1&th=1

 

[goosemfresh]

Pro Clip works great on my 200. Highly recommend

 

[IslandCruiser23]

ProClip + Quadlock works for my 200... Quadllock for my Bike and tractor...

 

[afgman786]

I wanted something that didn't clip onto vents, block the entire vent, or hang off the dash pad so I scanned and designed a fitted mount for the 08-15 LX if anybody is interested. Comes in charging, non charger, and quad lock variants, depending on budget. 3D printed in ASA and the bodyworked/painted to match the dash. Can be found via my etsy storefront.

https://yotaforge3d.etsy.com/listing/4295412492

View attachment 3916094

View attachment 3916095

Can't wait for this to come in the mail. Had a regular mag mount there and cause of the curve it didn't stick properly

 

[UT08LX570]

Can't wait for this to come in the mail. Had a regular mag mount there and cause of the curve it didn't stick properly

Exactly my scenario and desire to design this. If you have any feedback or different ideas once installed, please let me know!

 

[SquirrelDinner]

Offroam all aluminum base and mag-safe wireless charger. Works great.

How does the magsafe do offroad? do you have a case on your phone?

 

[bhakjdlmn1]

Sure, here you go. You'll want to cut the Lisen charger arm at the red line, with a dremel/angle grinder/hack saw/whatever you have. The stem then slides into the receiving hole with a snug fit.

It all works great and has spent hundreds of miles on the worst washboards and rock crawling. The 3D print should be printed in PETG to hold up to heat. It clips in positively in the vents. If the magnets holding the phone aren't strong enough, it's likely due to too bulky of a phone case. It works great and things are nice and tight without any vibration.

Just following up after a little while with TeCK's solution. It's nice! The phone mount is pretty solid (wobbles just a little bit, might want to use a higher temp plastic like ASA or ABS next time) and the phone position is good. Basically as high as it can be without obstructing any forward view.

 

[TomEf]

I wanted something that didn't clip onto vents, block the entire vent, or hang off the dash pad so I scanned and designed a fitted mount for the 08-15 LX if anybody is interested. Comes in charging, non charger, and quad lock variants, depending on budget. 3D printed in ASA and the bodyworked/painted to match the dash. Can be found via my etsy storefront.

https://yotaforge3d.etsy.com/listing/4295412492

View attachment 3916094

View attachment 3916095

Did you post these up in a Facebook group or two a while back? I was interested but it kinda fell off my radar with some busy summer stuff.

 

[UT08LX570]

Did you post these up in a Facebook group or two a while back? I was interested but it kinda fell off my radar with some busy summer stuff.

Yessir! I've got a couple products for the 200 series, that phone mount is one of my more popular ones.

https://www.etsy.com/shop/YotaForge3D