Wanted FJ60 Manual (1 Viewer)

[Man Jerk]

Re: GAS TANK

Yea, the recall has been done. I dont' even need a tank after all. It was just the gas pickup. All rusted to pieces.

 

[Guest]

Re: fj40 ignition

If it is a dash mount ignitionswitch, parts houses here(napa,carquest) have a universal key/ignition switch. I think they run $10-15. easy to put in.

 

[72cruiser]

Re: fj40 ignition

hey paul,

thanks for the info.

the more i've been thinking about it, the more i'd like to put an ignition with a bit more security anyways, so i'll probably end up going that route.

jonathan

 

[Guest]

Re: Rear View Mirror, and Wiper Motor, 73, 40

pablo, do you still need the mirror? I found one I forgot I had
it has the mount to screw to the windshield frame and the mirror. It has two mounting holes.

 

[pablo]

Re: Rear View Mirror, and Wiper Motor, 73, 40

Paul, the mirror on my rig has three springs that clamp to a post which is somehow connected to the windshield frame. Yes, I am still looking out a cracked mirror and need one.
Thanks
Pablo

 

[tennfj40]

Re: windshield wipers

*update* still need those wipers anybody got em

 

[FJ_MONSTER]

Re: WTB 3-speed t-case

hey buddy check it out: theres a guy in california that has an F/3spd/3spd case out of a 71 that wants to just give it away.hes on pirate4x4.com.the ad is in engines/tranyys for sale go like 3 -5 pages in and youll see it. theres your case

 

[tennfj40]

Re: stock fj40 shackles

i have them too if you still need them

 

[Cruiser_Nerd]

Re: Don't Laugh - FJ25 Parts Wanted

Woohoo, I don't check in for a few days and look what happens.

Tony, thanks, I'll contact you direct. The case is cast iron, single speed in/out, centered rear output w/ an external band parking brake.

Paul - thanks, the FJ25 used a 16" rim with a backspacing of about 2 1/2", with a single oval hole cut in the center section, w/ or w/o hub cap clips. As far as I know unique to the 25 although I've seen illustrations of very early 40's with the same wheel.

 

[ridge157]

2f valve cover

Anybody have a 2f valve cover in decent condition?

 

[LT]

75 - 77 FJ40 wiper motor

I'm looking for a 75 - 77 FJ40 wiper motor that is in good working order. I have a wiper motor from my old 78 that still works perfect. I tried using the 78 motor but the motor is too big for the shell casing. If anyone wants to trade or sell their motor let me know.

Travis

 

[eli77fj40]

Re: stock fj40 shackles

Tennfj40 where do you live and how much I am still lookin for some. Thanks.

 

[landcruisercentral]

!!!!Need Late Model Windshield Frame!!!!

Looking for a Late Model Windshield Frame "Complete" with motor and wipers and motor cover. Must Be RUST FREE !!! from States CA AZ NV NM ??? OR and WA. If it needs a little sand blasting thats ok but I'm not looking for somthing as thin as Tin Foil.

KEEP IT ROLLING

Curt From

landcruisercentral@yahoo.com

 

[onesprung60]

Re: 2f valve cover

I have one e-mail direct for a price

 

[PHAT MAX]

Re: !!!!Need Late Model Windshield Frame!!!!

good luck!

 

[Radd Cruisers]

Re: B-ENGINE MANUAL 1978 TO 1982 WANTED

I will email a person I know who has factory chassis manuels. Not sure about the engine manuel, I have one that will be pried from my dead cold fingers someday.

 

[Radd Cruisers]

Re: GAS TANK

I have a very clean unit from a BJ60? Not sure if it matters that there was diesel in it, sure is clean.
Live in Canada and not sure about shipping of such a item. Make me a offer.
Regards
Rob

 

[IDave]

Winch/Driveshaft

I'm looking for a working winch and driveshaft for an FJ40.

 

[cruzer]

Re: wanted:winch/w shaft and PTO power case

James quoted me 400-600 dollars complete..but never got back to me...i found one from another guy for 400 complete...with a "cracked" foot...well it turns out the foot FELL THE F### OFF IN SHIPPING so not so good a deal..but i got the entire set up from PTO gear to winch..the foot i can fix...just kind of upset that it wasn't stated outright in the dealings...also the PTO driveshaft lengths are diffrent from 3 to 4 spds because the tranny lenghts so you will have to get a 3spd driveshaft lenghtend if its on a 4spd set up...but other than that it should bolt right up...

Stew

 

[Guest]

fj-40 oem original soft top parts wanted

Anybody know of any OEM original Toyota soft top parts (Canvas, soft doors, bows, drop down tailgate,) I am trying to put together a set. Any help would be cool. Cheers you can email me at Ruperts@adelphia.net will pay finders fee. Thanks Brian :