Built FJ40 axles & tranny/t-case in NC

[R.K.]

FJ40 rear axle for sale. Set up for spring-over, 4.10 gearing, has disc brakes, stainless braided brake lines, and comes with spare axle shafts. $500

SM465 tranny mated to FJ40 t-case with aluminum adapter plate. Tranny has recent rebuild. Tranny has input collar to be mounted behind FJ40 straight 6 engine. Transfer case is twin sticked, has t-case saver installed, and has AA cross member. The 3-speed bellhousing is included to allow this unit to be mounted to a Cruiser engine. Will also include the .120" wall tube rear driveshaft from the set-up (is long enough for spring over with flipped rear springs). $700

FJ40 front axle. Axle is set up for spring over, knuckles have been cut/turned 16 deg, has armored removable front diff cover, 4.10 gearing with LockRight locker, 4340 cromo inner shafts and birfields, All-Pro spindle stud kit, minitruck knuckles, high steer, FJ60 calipers and rotors, Aisin hubs, U-bolts and plates included. Axle has been recently rebuilt. $1000

The rear axle and tranny/t-case are located in Roxboro, NC and the front axle is in Holly Springs, NC (near Raleigh). No shipping. Buy both axles and you'll have a bolt-on spring over.

R.K.

 

[JJS]

I'll hit you up in a couple months to see if you still have it, man. I'm moving that way. Good luck selling it in the interim.

 

[Eskimo]

up she goes..

 

[Eskimo]

bump..

 

[Sputnik40]

RK - What're you building up now? Let me know if you end up parting I'd be interested in a tight fine spline 4:10.

 

[Eskimo]

RK - What're you building up now? Let me know if you end up parting I'd be interested in a tight fine spline 4:10.

He's keeping Toy axles, but now running my old centered cruiser rear to better go with his new driveline...

 

[Eskimo]

Might consider parting the front axle.. interest?

 

[Sputnik40]

Looking for a fine spline front diff, but his might be too thrashed to be reliable enough for me.

If you part - I'd be interested in the spindle studs - maybe the whole knuckles as I can't see pulling just the studs? Same steering arm bolt pattern as FJ60 correct? What studs are in place for the steering arms...

Might consider parting the front axle.. interest?

 

[Eskimo]

I'd want to sell the whole knuckle, but preferrably the whole knucle out for someone upgrading from drums..

Yeah, FJ60/minitruck/late FJ40 knuckles, all the same.. stock studs. I check the torque daily, and have NEVER broken a stud, nor has anyone who started torquing them regularly..

 

[Eskimo]

TTT...

 

[dukebluerog]

wish I could afford both front and rear axles w/disc brakes....thinking about converting my drum brakes (67FJ40) to disc brakes...

 

[Sputnik40]

This is just a sik deal - surprised no-one has gone for it yet... Saw R.K.'s 40 at the top of the chute on Schoolbus last week - looking good.

If you end up parting, I'd be interested in the rear drive shaft if it's a double carden, the twin stik if I can use it on a similar setup but where I use the AA 4.5" adapter, and maybe one or both of the Asins for spares. I've got most everything else so far...

Good luck - anyone considering building up a wheeler should jump on this package - it's a steal!

 

[DBrown2]

AHH guys I think this is long gone...

 

[R.K.]

Yes, it has all been sold. Sorry for not updating the post, I've been busy lately.

R.K.

 

[dukebluerog]

dang...my loss....R.K., do u know anyone who may b selling front/rear axles w/disc brakes???...thanks..