Parting Out 88 fj62 part out, drivetrain is gone

[cwwfj60]

which plug/wiring do you need? I am using this engine for my own swap so anything that I need for that will be a no, but it is going into a 60 so it may not be used, let me know what it is.

 

[cwwfj60]

Do you still have the front panel (valance ) where the trun signals bolt in. I'll take the truns signals is they are in good shape.

steve

The trun signals is are in good shape. Lol, they are in decent shape, one very small chip on the pass side, and the valence is in pretty good shape, with some surface rust along the bottom edge. If you think you want it I will pull it and post pictures.

 

[KGB007]

Hi, need fuel tank. How much shipped to 93101?

 

[cwwfj60]

ya me too! Ha! sorry mine's junk.....

 

[ChaserFJ60]

How much for the front passenger seat belt assembly and their pillars that cover them??

 

[moiremusic]

I need a full set of locks, ignition, and keys for an FJ62, including left/rightdoor locks, rear door lock, ignition, fuel door lock, and glove box lock.

 

[cwwfj60]

Sorry, no key, ignition cylinder is gone

 

[Telly]

So what is up with the front seat? Thanks.

 

[cwwfj60]

sorry Telly, I pulled the seats apart. The cover on the passenger was torn around the bottom edge but the foam was good or fair condition. The drivers cover is in pretty good shape minus a small hole in the outside vinyl part (see picture). Also the metal rod that runs around the bottom of the seat for the hog rings is a little rusty, not bad but you can kinda feel the grit that is in that little sewed up part. So basically I got the upper and lower foam and fabric to make a good driver's seat. I got a couple pictures let me know if you need more. I'm guessing shipping will be around $30 ish and let me know if you want door panels too, I got all 4 in pretty good condition.

 

[Telly]

Thanks Cody. I will take the seat covers and foam as pictured. Let's connect off line to discuss the details.

 

[Bowling4$]

If Telly doesn't take the seat covers I will.

 

[fl4031003]

Cody, still count me in for that metal cut we discussed. No hurry.

Jeff

 

[Lickys60]

I am looking for an AC amplifier. It's a little circuit board under the glove box that is attached to the plug in this picture....

 

[mulchiro]

I saw you sold the battery hold down, did you sell the battery tray?

 

[LAgallegos]

Hey I'm curious about the radio, and the plastic pieces on each door between the frame and the door(i think they are considered molding)?

 

[cwwfj60]

Ok quick update:

Seats sold
steering column sold

The metal cut we discussed (Jeff) should be available sometime in the next few weeks.

A/C amplifier was ruined, moisture got into that hole and corroded it badly

I still have the battery hold down and tray pm me if still interested

Radio is available, but like I said is not fully functioning, side chrome moldings are gone. PM for the radio

 

[cwwfj60]

Sorry I was wrong, tray is toast, hold down is available

 

[cwwfj60]

Notable pieces that are still available....

Rear seat bottom only in great shape.

All 4 door panels in great shape just need to be cleaned up.

Front grille center and driver side light bezel in decent shape, chrome is coming off like most. Pass side is toast.

Transmission and transfer case are most likely going to be sold now and I am also considering selling the axles. This truck is pretty rusty so once everything is pulled I'll evaluate condition/price and I may possibly hold on to the 4.11s but if anybody is interested in these parts let me know, make an offer and I'll probably change my mind....remember this truck only has 89k miles on it!

 

[DickM]

How about front fender vent grilles and gaskets-both sides?

 

[cwwfj60]

How about front fender vent grilles and gaskets-both sides?

Got'em! They are in decent shape, chrome is good, but the grey color on the inside is wearing off (see pics), could be made new if you taped off the chrome and sprayed the grey again, either way good pieces. Not sure what they are worth so make me an offer, shipping should be $6 ish. Let me know your address if you want them.