muffler

I’ve got the manifold tick, so I’m replacing with doug Thorley shorty headers. Figured I’d save on shipping and grab a Gibson exhaust as well so while it’s in the shop I’ll slap that on too. This will leave me with some spare parts. The old manifold(s) are trash but the exhaust/muffler from the...

Looking for a little welding project for myself when I am done messing with the axles. Previously when I did the exhaust on BeBe, my FJ60, I used a converter/adapter to go from the stock 2.25" exhaust up to the 2.5" from the down pipe back. Basically this was stock exhaust manifold until just...

The exhaust on my 97 is shot. Especially where the pipe goes over the crossmember by the rear axle, that has pounded itself almost flat after the exhaust mounts wore out. (Mounts have been repaired) When @NLXTACY turbo arrives :clap:, I will need a new exhaust. I was hoping to use @OTRAMM SS...

Forgive me if this is obvious or has been suggested before but I haven't run across it. For whatever reason, the spacing between the exhaust pipe and my '92 FJ80 rear cross member was tight enough to bang when driven on my 3/4 mi gravel driveway. After confirming that the mounting cushions...

Ok so I was hoping someone would chime in after the last few posts I made regarding the route I mocked up this weekend but alas all is still quiet. I’ve never done this stuff before. You all know me, I fumble my way through and soak up whatever suggestions folks throw at me that are in my...

Doug Thorley catback stainless steel exhaust system for 1999-2005 Land Cruiser / LX470. I ran it for a little over a year, but realized I'm an old man and wanted a quiet stock exhaust system. Overall in really good shape. You'll need two new clamps (any generic brand clamp would work) and you'll...

Im running a stock 1fz-fe, and it's time to replace my muffler. I'm considering going to 3" pipe all the way out. Was wondering if 3" would be beneficial at all, or just a waste of time and money. It's just that as I'm shopping for big can mufflers, I notice the 3" and 2.5" aren't much...

Hey guys.. i own a 1994 80 series land cruiser.. i have a 1hz non turbo engine.. so yesterday i removed my muffler and installed a new muffler.. the sound is really riced i dont like it.. so a friend of mine suggest me to remove the muffler and keep it straight without the muffler.. is it a good...

So Cal Nice clean one that goes behind cat to bring the twin cats into one pipe. $40 + shipping. Paypal OK

SoCal. Prices from $25 per item to $100. Shipping is available, but can be costly. However total cost will still be much less than new. From a Local car with no rust issues - Exhaust Manifolds Heat Shields Headpipes Y pipe Dual Cats Cat Heat shield 02 sensors Resonator etc. Send message...

Today I was driving back to work from lunch and heard a weird noise like squeaking of brakes, but I wasn't breaking. This was shortly followed by a very loud bang (backfire) and I immediately pulled over. The engine was still running just fine and when I let off the clutch it had power but now...

Looks like there are two main choices for direct bolt on muffler replacement for our 06' LX470. Clickable link ► Walker 55329 Clickable link ► Bosal 279-773 Rumored Walker has fitment issues can anyone confirm? Looking for an option that is wife approved. This is our travel vehicle and it see a...

I'm wanting a little rumble exhaust sound and don't want to spend the money for a DT exhaust system. Has anyone done a muffler delete? any problems with this? Also thinking about a Flomaster muffler but not sure the route I want to go. My 100 is not my DD so not worried about getting tired of...

Hey guys, I installed a 3inch muffler on my HDJ80 past weekend, and well here are some pros and cons that I found... Pros: 1- More Power, when accelerating the car just accelerates beastly. 2- More torque, when going uphill, it has more torque to stay on a High gear. 3- The sound... It is...

Does anyone sell a bolt on performance muffler for the 93-94 land cruiser, I see a borla for 95-97 but nothing else but stock for the 93-94, I want it to be a little bit louder than stock, what is the Bosal muffler, is that like a stock quiet replacement?

Anyone know of a good muffler shop in CLT-my last one in Raleigh lasted maybe 2 years....this happened while driving and scared the sh$t out of me.

Has anyone had any experience with Gibson mufflers? I've been doing so work to the underneath of my 97 LC, new diff and tranny fluid has morphed into new bushings, new tie rods, powder coating various bits, and now... Looking at that rusty exhaust with 9 bends and crushed pipe... i think we can...

From now until October 31, 2015 save on our popular Ultra Flo Welded or VT drone-free mufflers. Click the link below for all the details and check with your favorite retailer on pricing. DynoMax® Performance Exhaust Promotions