help

I replaced the heater core and evaporator and removed the dash. I cant figure out what this connector is or where it goes. Does anybody have ideas?

Greetings fellow enthusiasts, Things have begun to go south on my '10 LX with ~95k Miles. A few weeks back I flushed my AHC with 0 initial problems, I followed the guides posted here including using the Metal can AHC Oil and I bled multiple times until the fluid from bleeders was perfectly...

Hi all looking for some help, I purchased a 1972 fj40. The headlights are not working. There is power going to the headlight switch but when you pull the knob on the switch nothing happens. All the other lights work, but not the headlights. Any help would be appreciated.

These came on my 73 series. They look new, front and back; and I assumed they were the Toyota part number 42601-60262-03; however, @lynchmob just taught me to count the openings and duh.... they are something else. Anyone know if these are OEM or aftermarket?

I’m trying to set the toe in on my 80. Yes I’m using the FSM I’m reading this as 2MM each side ?

Hey y’all- new to the Landcruiser life. Picked up a triple locked 80 Series yesterday (‘94) anticipating a project. After driving for about 10 minutes, I noticed a whining sound when hitting around 25mph. It took no time for this to turn into a horrible grinding/ rattling sound. Sounds...

My belts started squeaking on startup and when I went to look I realized the lower bolt on the alternator is missing. While looking over the engine I also noticed that two of the three bolts holding the power steering reservoir are missing. I have a 1990 HZJ75 and currently located in Reno, NV...

Anyone from this area know a good mechanic that knows their stuff. I had some issues driving out here for work that continue to get worse and need a shop that know their stuff. I'm in Montpellier but the shop doesn't have to be here. Thanks!

I have a 1974 FJ40 that I need help with on how to run the vacuum lines based on my setup. I have an earlier emissions control device )which I would like to utilize it since I just recently bought one from BTB products) an 75 stock carb, I believe a 78 distributor, and a 2f motor with an 2f...

Good morning (As I write this) my dear Mud community :) My name is Josh Wells and I'm desperately looking for someone to ship a 3/4 tub only from Seattle, Washington to Paradise, CA. The tub is being purchased for my 17 year old son and I wanted to give you a brief back story on him to help you...

As the title says I am looking for help in adjusting the OEM cross rails for the roof rack. I have a '23 GX that came with the rack & rails installed. I just purchased a Thule cargo carrier and need to move the cross rails to get the Thule secured. Didn't find any instruction in the owners...

After a bit of help... Aussie, RH FJ62 with a 3F (not 3FE). The cable going to the Idle-control valve on the back side of the carbie has a big square connector (its disconnected in the PIC). The next connector down does not seem to be connected to anything ( its a single blade connection...

My 1996 LX450 with 350,000 miles in rough condition was involved in an accident involving the front and rear bumpers. I wasn’t at fault, but the insurance company has declared the vehicle a total loss. Unfortunately, they claim the actual cash value is only $1,200. I’m looking for some help to...

I can't believe I'm posting another catastrophic failure thread, but...here I am. For those not in the know, I recently had an inexplicable H55f failure, remedied by a new unit built by @cruisermatt, which due to the freight company (YRC Freight)'s careless treatment, took two tries over two+...

Beach n Toys group I reached out to Frank? And he suggested that I post this here. I am reaching out to this group because your the experts in San Diego and I have a FJ40 build in my garage and need help getting it finished. It’s close but I need help wiring the rig and getting correctly setup...

Hello all, this is mounted under the distributor of a 1979 2F. I’ve never seen one but likely somebody knows what it is? It has apparently been disconnected for some time but it has a set of hefty bolts attaching it to the block and some odd passage connection further up into the block

I have a 1993 HDJ81 Imported from Japan with a 1HDT 4.2L turbo diesel. Running 33 inch tires on the 16 inch wheels. Axle gear ratio I believe is 4.11. Thinking about running 4.88 or 5.13s to help with the turbo lag that is present from a dead stop to acceleration. Seems like the turbo kicks in...

I am a bit confused by this and I'm curious is anyone has been in a similar situation: I have a 1993 HDJ80 with a 1HDT. Stock CT26 Turbo, Stock Tune, etc. I recently built and installed a front mount air-to-air intercooler in the hopes of lowering my EGTs on long hauls and mountain passes...

I need some help. I spent quite a bit of time trying to diagnose the issue with my CC to no avail. Here is where I am at: 1.Light comes on the dash when I push the button. 2. I went through the first set of steps to diagnose the Set/Coast circuit and that is normal. (It flashes as it should)...

Hello murders, I'm doing all my front axle work next week and I'd like to paint the front axle and shock mounts. Will eventually be painting the whole frame as I move from front to back. Just need to decide on what paint to use. I won't be sanding too much because in generally it's pretty rust...