help

This thing was laying on top of the engine cover and fell out when I removed it. Any idea what it is?

The AC lines below my passenger door are showing signs of leaking. I took off the insulation and the brackets and could not find the source of the leak. I took it to a local shop to have the AC recharged after replacing the AC condenser and they also could not find a leak and said the system...

hi there, I have a 1991 3fe fj80 Land Cruiser that I need to replace coolant hoses on, I've been looking all over and can't find the part numbers, if anyone could tell me the part numbers or where to buy a set of good hoses I would greatly appreciate it, thx

Greetings, I just need some affirmation of what I think I am already going to do. I currently own a 2003 100 Series with 275k miles that I've had for about 7 years. Prior to that I had a 2000 100 for about 7 years. I also own a 2015 GX with 180k miles that I've had since 60k miles (wife's DD)...

I’ve been stalking FB marketplace for a spring green 40 for a year or so now and I came across this one. I’m wondering if anyone sees any major red flags in the pictures. I’m still extremely new to 40’s so please bear with me. Also, I know value can fluctuate significantly depending on how the...

I have a 1989 FJ62 and I have been looking at IH8MUD for help fixing my vehicle for years without creating an account. Finally registered for an account today and I think it’s going to be much better! I am replacing my vehicle’s water pump (in and of itself a difficult task for me) and I saw a...

Hey everyone So, I traded my 12v 8274 to someone who said they had the factory 24v Toyota winch. I was silly and said ok sure lets do it thinking that it was just a 24v version of the 8274 and NOT some silly rare winch that you cant get parts for. Anyway, before I can it and just track down a...

Current height with OME shock/spring height with no additional weight: Front - 22" center hub to fender Rear - 23 1/2" center hub to fender I want to move to a Dobinson IMS kit w/ C59-222V 2.0″ front and C59-223v 1.75″ rear. I want to also add a FR Slimline II rack. Best guess on height is...

Hi, all. Sorry English is not my native tongue. Please forgive me if I don't say it clearly. Long story short, my LX 570 had the heat valley leak problem, and It has been parking in my garage for about 2 months. Today I fixed the leak, but after I started the car, and turned the heater on to...

I have been driving my 2000 100 Series (201k) for about two years now. My dad actually bought the truck brand new back in the day and I took ownership as my daily driver after college. Decided I am going to go with the Ironman or ARB bumpers for my first modifications. Two questions - 1. If...

Have been struggling with this for three days on and off. Nothing on line, even in the Toyota van tech forums. Trying to find the low side port to charge my AC system. I have found the stickers where it has been converted to 134a. I figured the stickers would be close to where it gets charged...

Hey all, I don’t post on here a ton as my FJ62 is is many pieces and I’m slowly rebuilding. I am getting to the point where I can’t find a solid lead on a gen 4/6l80 combo anywhere. Most reasonable donors are more expensive than. FB marketplace “ran fine when I pulled it” are sketchy. Anyone...

On a trip from Calgary to Alaska and my 2003 LX470 started the N to D and N to R clunk. Not super bad, but worse when hot. Read all we can with limited cell signal, so have seen the common causes. Question is what are our odds of making it 2000 kms? And second, can I disconnect the drive shaft...

Help please! I have purchased a LX 450 97. I would like to replace the driver side rear corner bumper but I need the mounting brackets and assembly. I know the bumper cover is different in the LC than the 450 but are the brackets and assembly the same? I’m hearing different opinions. Also I...

Anyone have a rear end carrier 3:73 gears for a FJ60?? Just lost my pinion gear! Removed the rear axle but the pinion gear is binding. Can’t move Anyone close let me know! 310-717-4306 Jorge

My daughter has our 80 in Annandale, VA just outside the beltway. The LF wheel began smoking and its birfield grease on the inboard surface of backing plate. As routine maintenance, I added grease to the plug about 500 miles ago, checked tightness of the 4 lower knuckle nuts and left town. Then...

Hey gang. I paid someone to retrofit some HID projectors into my 2002 headlamps, and they didn't do a great job. In fact, they did a really, really bad job. Aside from a half-melted tab and scratched shrouds, the headlight housings no longer adjust up and down, OR right and left. I suspect it's...

Hello, I need help with the wiring diagram of this ECM from a 98' LX470. Specifically I need to find Knock sensor bank 1 KNK1 and Knock sensor bank 2 KNK2 wire. I've searched around manuals online but to no avail. any help would be greatly appreciated.

I’m chasing down a no A/C issue on my 2006 LX470. Previous owner mentioned that there was “an ac leak under the hood”. Foolishly at the time I figured it would be an easy fix and didn’t ask where the leak was. Now I’m working on fixing the AC and can’t seem to find any leaks or bad lines...

Hi everyone, Hoping to get some ideas on what may be causing this grinding noise which seems to be coming from the transfer case area. The truck is a 1979 BJ40 with a 4 speed transmission. The noise occurs in all 4 forward gears (while moving) and does not occur in reverse. When the clutch is...