help

Hopefully a quick question, my 84 FJ60 has high CO‘s at high idle test. I’ve rebuilt the carb, adjusted the valves and timing repaired the AI system, new plugs, wire, cap and rotor, verified no intake leaks. Adjusted the carb while on the sniffer. I was able to get HC’s and CO’s in spec at idle...

We did a Radiator Replacement I have a outlet Pipe leak on the pipe to the Engine block. It is a car passed down from a friend who passed during Co-vid and we are trying to get it back up and running as a nod to him. Is there any sources in the US to get parts?

Hey everyone, I'm new to the forum, the rules said I had to post an introduction, so here I am. Howdy. I've got a question pertaining to the alternator/regulator of an FJ40 I'm doing some electrical work on. This thing has had many owners and the wiring has been modified a bit by other...

2007 LC 265,000 miles replaced upper and lower control arms, wheel bearings, one axle in the last two years. Steering rack was replaced about 5 years ago. Slight sensor lift on 34" tires. Every so often and more recently when I turn the truck left (like making a left onto a side street) the...

Does anybody know where this brass elbow hose is supposed to go to?

120k 2014 GX460 all stock. Over the last 20k miles I have developed what I personally know as "Toyota truck s***ty front end syndrome". I don't know if there really is a universal syndrome, but I do know that I have observed similar symptoms on various 4runners, Tacomas, and now my GX. It...

I screwed up. Rebuilding my 83 FJ40 carb and didn't record the numbers on the long slow jets. One is #65 & other is #90. Need to know which is Primary and which is Secondary. Don't know if it matters but I'm at 5000' elevation. Thanks, Jim

Looking to obtain a VIN from a new 2022/2023 Prado 150 VX Matte Black edition. Really just need it for parts verification. None of the overseas sites post vins like they do here. GCC because left hand drive and can make sure headlight part #are correct for use here.

Just paid what is probably a record high to get my trans rebuilt, the genius forgot to torque the drain plug back so it fell out somewhere on the highway and I drove the gx a couple miles while it leaked all over the place. When I finally parked and turned it off is when it really started...

Hello all. Continuing in my 80 series resto- Have codes 25, 26, and 71. Running lean, running rich, and EGR System. It’s worth noting the vehicle is running fine over all- no noticeable issues. Any advice on where to start?

Yesterday we took the Landcruiser out for about a 150 mile round trip through some elevations. When we got home and off the highway at a light the oil pressure as read by the gauge dropped to a seriously low level and the car started vibrating a bit at idle. By seriously low I mean there was...

I’m just about to paint the FJ 40 and I have the transmission tunnel off and I noticed that my transmission and transfer case linkages do not match the holes on my cover. Any help would be appreciated

June 1975 FJ40 I've got some weirdness that I'm trying to solve. PO took a shortcut and wired around the original flasher plug and added another direct wired to the turn signal switch. I am attempting to clean up this work. I replaced the weird wiring with a current flasher plug as seen in...

Yes, I did search but couldn't find an answer. If there is a thread for this please drop a link. I have not towed any load that needed a trailer brake so nothing heavy. I am towing a trailer about 3500# and the back is sagging and I get some bobbing up and down at the hitch. I have added a...

I found a thread that shows the location on the fj62 harness, but my harness looks different than that one. It's all covered with alot more corrugated plastic tubing. Here are the images of the 62 harness showing ground binding block locations. They come from this post(towards the bottom) Where...

Firstly, thank those who answered my thread a few days ago about the type of master cylinder I needed. I recently bought a 96 FZJ80 VX limited imported 102,000km (63k miles) from Japan. It's in pretty incredible condition; there are a few minor things I already took care of noted in the...

I'm needed some help trying to find the right car on a second hand market. - what kms do I look for? - what type do I look for? - what other general things do I look for? Price range is around $13000 aud and would probably push $15000 aud I'm new here and want to go bush.

I am very new to the platform and after having looked at a few for sale and being disappointed by the overwhelming amount of paint work I'm finding. I've been involved in the Porsche Audi scene for 25 years and in most cases we deduct a minimum of 20% of it's declared value if there's evidence...

Hey guys - we have a 2003 LX470 that my wife drove to Asheville to visit family. I am worried the catalytic converter on it may be toast. Is there somewhere in town that she could get it looked at on the weekend? I'm worried about her potentially driving it home - two kids with her too.

I have a 1996 FJZ80 imported from Japan (JDM, RHD, etc, etc), it's fantastic! I hate to start another thread on the Spongey brake issue (I've read so many), but as I follow the FSM, I have run into a dilemma. The Brake Master Cylinder has 2 bolt holes onto the booster instead of 4, which...