I bought an 80 with a bad head- and the owners records showed Toyota replacing the bottom end with a new $6000 block at a Toyota dealer.:oops: I pulled the motor/trans and kept it as a spare and now i dont need it. I pulled the head to use for another project and also just to see what an...
My 95 has a blown head gasket after flogging it to death pulling a box trailer for a month for work while searching for a new V8 Sequoia to replace the one my daughter totaled. I'm getting ready to replace the HG in the truck, and have a good spare engine (also with a minor HG leak) to mix/...
Need a late 2F head which came off a 1986 FJ60.
Casting is 61040.
Will pickup in Dallas/Houston/San Antonio/Austin area.
PM me with pictures and cost
Thanks
Ernie
Howdy central Texas folks,
Looks like my late 1986 2F head has a crack under an exhaust seat.
So I am looking for a late 2F head that does not have cracks to complete my rebuild.
The casting is 61040.
Please tell me what you have.
Thanks
Ernie
Hello, I have recently purchesed a 1980 Toyota Pickup, SR5 Longbed 2wd, 20r engine. When I bought the truck the engine was only running on 2 cylinders, had a lot of carb problems, was burning oil, and possible head gasket. I rebuilt the engine, put on a new Carburetor (the weber 32/36) and...
275,000 miles and 20 years. Started leaking externally at the back of the PS head as well as just above the engine mounts on both heads. Truck ran fine and an inspection of the cylinder bores didn't give me any reason to believe it was leaking internally but I'm sure it was only a matter of...
Hi all,
Removed my Remflex gasket to try to reseal it (was leaking). But am trying to figure out how I can get the old stuff off without spilling into the ports.
Ideas? I have some fine steel wool. And was just gunna jam paper towels on there then pull em out after..
Dan
Hey Lads,
Does a 3b head 11101-58014 small valve fit on a 11101-58010 big valve block? I’ve gotten stitched up with my new head and now probably is a expensive paper weight.
Cheers!
Hey Lads!
Ive got a 1982 60 series Landcruiser with the trusty 3B in it. I pulled it apart to give it a refresh and I discovered the head is cracked.
Since it is the old style 3B with the head bolts down the middle (big valve 11111-58010) it is near impossible to find a used non cracked...
Hey guys,
I'm finishing up this motor before putting it into the truck and forgot to take a pic of where the heater nipple and the two unions for the temperature senders go on the head; could somebody show me with a picture? This is a 1974 F.5.
I replaced the original three-piece heater hose...
So my head gasket blew. I took it to Land Cruiser Northwest to get it looked at because I had a P0306 code and the injector came unplugged. But I had an exhaust leak so I was going to have them fix it. They took a look over it and did some tests and told me the head gasket was blown. They quoted...
Looking to order a bolt on ready head replacement this week for my 95 series. Seems like a few reliable options out of Australia - the one I have been in communication with is Mr Cylinder Head.
Looking for some advice:
1) Mr Cylinder Head in general: anyone had any bad experiences? The kit...
Ok people, clearly I didnt do my homework...I bought a 2000 Lexus LX 470 back in July 2022 with 157,000 miles on it and after bringing it to three different mechanics the truth is inevitable, that I NEED head gaskets, but probably more realistic, I need a new motor.
Im trying to decide if the...
Some very small fisher cracks between valve seats. Pretty common, machine shop said I should run it, but I had a new one on the shelf already. Already been hot tanked and checked for flat. This one is $500 + shipping
location: Western Montana
I don't like my exhaust set up, it's duals hanging low off each side. I don't care for the look or the sound and I want to change over to a single exhaust and muffler exiting the rear of the truck. My set up is a 350 V8 with rams head exhaust manifolds so I think I am part way there. I have...
I mostly drive with TEMS set to number 3, but i occasionally change to 1 or 2 for more comfort.
So yesterday i set it to 2 as i was on some pot-holed road. I was obviously driving extrememy slowly. When i entered a pothole, my head badly knocked against the car door. Couldnt believe it. Never...