My father repairs tractors and says he always uses it, but ive never seen anyone else do this. Permatex® Copper Spray-A-Gasket® High-Temp Sealant, 12 OZ – Permatex - https://www.permatex.com/products/gasketing/gasket-sealants/permatex-copper-spray-a-gasket-high-temp-sealant-12-oz/ I think its...
I have two heads: 60051 (1974) and 61031 (1977)
I have read many threads here, but not many really had comparisons between F.5 and F2 heads. Especially with the pictures.
I try my best to summarize some information here. All my measurements are not 100% accurate, but give some idea of the size...
A thread for Red (cause someone was Bitchin! 🤣.) Thats why i start this thread. Red might be going out to pasture. She been sitting for a couple months because of rain. The clutch master is in and working, clutch slave is working, still wont go into gear after all the adjusting!!! 😡 need to...
Couldn't find Toyota spec sheets for head bolts/washers or main bolts. @OGBeno says I never will. So I sent a new head bolt/washer to my ARP contact, hoping they might have an exact fit off-the-shelf so we don't have to mess around with Opel and Supra studs. I'm told they need more information...
Hi im currenty at a stand still with an engine build. My 1970 F155 engine has gone out and its beyond repair. I picked up a really clean 3FE out of a 1992 FJ80. was told it was rebuilt 1500 miles ago. well got it home did leak down and compression. And its horrible 50% blow by past rings in 4...
Took the head off my 3B, the crankshaft broke apart in a couple places but the top end is unharmed. Head gasket was fine and fully intact and the head doesn't have any visible cracks besides on the precups which from what I understand is normal. Can also give all the head bolts I pulled, they...
Hey all, I'm looking for those studs that thread into the head, and hold the valve supports and valve cover on. I found one on ebay but I was wondering if anyone knew the part number (or a vendor who ships quicker)? Can't find much info. This is what I'm referring to: EBAY LINK
CD head unit from AUS spec 1996 GXL 80 Series. Dealer option with owners manual.
CD non functional for unknown reasons but Cassette works.
105$ Shipped
Picked up a used T-case out of a 97 cruiser with 120k on it from a guy here on Mud with a newly installed Cruiser Outfitters part time kit, his build went a different direction and I bought from him as a spare. I have an used head from another '97 cruiser that needs to be rebuilt, fully...
Hi I’m looking to buy the two compression fitting nuts that go from the block to the head. I lost mine and can’t find a place where buy, I already looked in SOR but they only have the pipe and ferrules. Also order some from McMaster but they don’t fit, according to my measurement they are...
My head is cracked, machinist says it's too big to repair.
Anyone got a good head? Willing to drive pretty far, or arrange shipping.
If the head condition is unknown (not-magnafluxed for cracks) I'd need a very low price, or assurance that you'd be willing to refund
-b
Putting the engine back together after a valve job.
Where the rocker arm assembly meets the head, there is no sealant or gasket. With the oil passage going through the two parts, wont oil leak out the side of that joint and reduce oil pressure to the rockers? Should some sort of sealant around...
I have a 1971 FJ40 Land cruiser that I purchased as a parts vehicle for a rebuild of another. I have a lot of parts I will not need. I will ship smaller parts, however, larger parts are pick up only in Virginia Beach VA. Below is the removed items I have along with a pic of the parts vehicle...
I have a few things that I ended up not needing for my engine rebuild. These are brand new, OEM parts. Might trade for ARP head bolts or cometic gasket.
Head Gasket- $75 (SOLD)
Oil Cap- $10
Head Bolt Set (Qty 14)- $175
Parts are in OKC, OK.
I have a freshly rebuilt 2F Head for sale that is ready to go for someone's domed piston 2F build.
All work on the rebuild was done by Kennedy Performance here in Lexington, KY. (I can furnish the receipt verifying the work done to the buyer or prospective buyers). The following list was...
Hi everyone,
This is my first post here on IH8MUD. I have been successfully wrenching (thanks to forums like these) on a few Toyotas ( 95 T100 5vz-fe w/ 459km on it, and more recently a 85 Hiace Pickup 2L with 92km) now for a while. I find much of the information here useful and I am hoping to...
Hi all. As part of my 2lte upgrades roject I'm researching head replacement options.. I know a 3l head will fit but I'm intrigued with a 1KZTE short valve head.. it's the bigger intake & exhaust valves..
So will this head fit my 2lte block??
Thanks for your replies in advance..
I bought a well maintained ‘97 LX450 from a neighbor a few weeks ago. It has 188K miles, just had an oil change and it was running like a top before I took it to a local Midas yesterday for new belts (a/c, alternator and v-belt). Midas also replaced the fluid in both differentials and my...
I've been looking into this a bit because I got an incorrect (ports too big) fuel primer head a while back and didn't realise until then there were two sizes of fuel line fitted to 80's for the Australian market.
So I went looking in toyodiy at the p/n's and discovered that for mine (1992) the...
I need help identifying compatadability with my block and head. my block vin is 232080 and I have attached some pictures of the head. I'm trying to change the head gasket but can't figure out what gasket to get and if the head I'm using will work. I think the block is an early model f engine I'm...