gauge

I just noticed the low fuel warning lights up even the gauge needle isn't pointing to the last tick mark. It has never happened before. Usually the light goes on at the last tick or slightly below. Any ideas?

I need some help. I've read over all the forums and I'm still a bit stuck. My fuel gauge always shows empty. Following the advice of many others I started with the fuel sending unit. The unit itself is fairly new and with a multimeter it registered about 16 ohms on full and 119 ohms empty...

Ok, so another thing I'm wondering about. I'm building a fiberglass dash. And I bought a digital gauge set, because it was a GPS speedometer. So doesn't have to read off of anything and doesn't matter what tire size etc... But after getting it I kind of would like to run the stock gauges. So has...

Good evening! I have what I am now sure is an early gauge cluster (speedo to 100mph, gauges are in order of oil, temp, fuel, amm). Also, gauges have a "rounded bottom" vs. the new yr gauges. My temp gauge is not working, always pegged at H, and needs replacement. My question is, will the newer...

hi all Would b my first post here.. In my part of the world the temps really going high and it has started showing some effect on my LJ78 with a swapped 1KZ .. Its running the same RADIATOR that of 2L engine.. Just wana know if I need to change the Radiator as the engine has gone big?

Evening all! I am in need of a functional temp gauge for a 73 F engine. The rest of my gauge cluster works, but the temp gauge does not work. Thank you in advance! Dave

85 FJ60 have an issue with the temperature gauge it only moves up a small amount above the bottom of the white, not mid way through the white like it normally did. I thought it was the sender on the engine block so I removed the sender place it in a glass of water and measured the resistance...

Could I have bumped something down there?? Seems like quite a coincidence.

Yeah....I know, If its running and not knocking...its probably OK. But I just can't stand the factory gauge. After warm up, basically indicates ZERO (or right at it) at idle (650 rpm). It DOES rise immediately with engine rpm, but I'd just like to be able to see numbers instead of an indicator...

Hey everyone, I promised I've searched a ton so forgive my first post being a question and hopefully this isn't something I should have found and just missed. I just picked up my LX470 last week and got a deal on it since it had a few minor issues (half the third row missing, SRS light, etc...

UPDATE: 04/06/2017 I am moving ahead with option 1. I've made considerable progress on the hardware and software design and should have prototype hardware within next few weeks. Feature set looks like this: Clock w/ Date (12 or 24 Hour Time) 3 Temperature Inputs (Compatible with ALL VDO...

I started noticing my oil pressure gauge complete dead about four months ago, took it to a trusted Toyota master technician, he replaced the solenoid sender, worked for a day went bad again, took it back, he completely cleaned out the instrument panel and cleaned the circuit board from minor...

Anyone know what metal gauge was used on the floors, door sills, inner and outer rockers? It seems as if the door sills slightly heavier gauge than the floor, but it's tough to tell because everything is a bit rusty. Any help would be appreciated.

This cluster came on my 1979 parts car. I can verify that all meters work (besides AMP Meter). The 1979 FJ40 have a separate AMP meter plug and this cluster is not for 1979 and up but I am sure it will work. The cluster is in great condition, just a little dirty on the face. $200 shipped. I...

Is there a transmission temp xgauge you use? And what is a good temp for our transmissions? I found a xgauge code on line but it measures in (-) degree F.

Another cluster. Rusted face plate. Working condition unknown $60.00 Plus shipping

This fj40 gauge cluster is in good condition. Worked when removed. $100.00

Getting ready to wire up a 8274 that I don't expect to see heavy use. I did get a blue sea marine battery isolator to be able to switch off the positive under the hood until needed. Planning on using copper 2 gauge wire, but wanted to get thoughts and what are good sources? Thanks,

I'm going to make a new wiring harness for the tail lights on my 45. I'm Going All Coolerman I'm not getting any answers over on the 45 forum. What i need to know is the gauge of the wires that run to the taillights. Running lights, brakes, reverse, turn signals and side markers. Anyone know?

Hello, Selling the EGT and boost gauge, EGT comes with a brand new probe, boost just needs a boost hose comes with compression fitting. Both gauges have the wires cut about 3" long, can be easily spliced, instructions can be found on their web site. Nick