gauge

Hello Folks! I've always had a temp gauge that sometimes like to peg itself out above hot, even though the truck is running fine. It will do it maybe once every 30 minutes, for 30 seconds or so. Not that big of a deal, but I noticed yesterday that the fuel gauge did the same thing (pegged...

Converted all interior lights to LED. I love the brightness and overall aesthetics of the change. I got em all too. Here's the issue. ONE light is having an "always on" issue. My CDL light on the instrument cluster is dimly lit all the time. I know it is a bulb/wattage/current issue because it...

Hey guys! I’m selling some gauge holders for 40’s that mount to the original plastics on the column. I also sell a few other items if you could check them out 😊 Let me know if you have any feedback or other items you's like me to make :) P32 Manufacturing - Gauge Pods

New to me ‘72 55. Going through some immediate issues. Would love to have a functional gas gauge. I think I have read through maybe 20 threads on this issue. My float/sender is functioning properly (checked with ohm-meter) Contacts on the back of the gauge look clean, the ebrake and charge...

Absolutely fuming mad, but in short someone sprayed Febreze into my truck, some landed on the plastic in front of the gauge cluster and it is now etched. I’ve tried using cleaners and nothing will remove it. So I need to replace it. Are there any videos or instructions on how I can remove and...

The weather in Texas is solidly around 105 in the afternoons right now. When my truck is idling, the AC starts to blow warm and the engine temperature starts creeping up. Coolant is just a little bit below the full line and when I’m driving, the AC blows cold all the time. Any recommendations?

1977 is running about 177° (infra red gun) at the freeze plugs when warmed up and idling but the temp gauge slowly moved all the way right as it warmed up. I think the gauge may be from a '79 (the amp meter is). Is the sender from a '79 different than a '77? thanks

I installed a boost gauge just to see how much boost my truck is making. I only see maybe 2-3 psi and 4.5 psi in higher rpms with heavier throttle. Does it seem normal?

I'm hoping to catch some more input by putting this in its own thread. Relating to my solid state regulator project, but this could also help with others who don't go with the upgrade once it's available. What I'm trying to do is figure a good point for baseline calibration of the fuel gauge...

Anyone have one? would be willing to rent or purchase. Thanks Mud

Does anyone have a known working gauge they'd like to part with? Will pay for the ride and a fair value! Really appreciate it. -Bison

Hey all, I have a problem with my gas gauge staying stuck at full after a fill up until some inconsistent amount of time when it finally reads correct. As of now, I have done 195 miles on a tank and it says i still have a full tank of gas. I replaced the sending unit in the gas tank and it...

What does the mud hive say about a good floor pump. I currently own a Silca floor pump w digital gauge. Hate it. Love the pump hate the gauge. It’s always off by a few psi and eats batteries likes they’re pez candies. Need to use it for road and mtn. I run tubeless and use a compressor at...

How typical is it for the fuel gauge to be inaccurate on the 80 Series when everything "looks" to be in good condition? Trying to determine if I am chasing results that are not realistic before doing the FSM procedure to test everything. My gauge often says there is less fuel than I really...

Pillar pod (gauge pod) designed to fit 2007+ 70 series. LHD models only. $150+ shipping

I have a 91 land cruiser and the gas gauge reads sometimes. When I fill up it reads full for awhile then after driving it goes to 0 or to half. If the level if anywhere above half it'll indicate randomly, but once its below half it reads 0. Low fuel light still works as it should. Any insight to...

I have a recently damaged water temp sensor on my 1990 24 volt 1pz. Confirmed today that this is the two wire unit running to connections 7 and 10 of the glow timer module as per the workshop manual. As soon as the wire severed I have no water temp reading on the dash cluster, just a constant...

Evening, What do people here generally see on their OEM oil pressure gauge w/ factory 2F motor!? I’m sure these aren’t incredibly accurate gauges, but, just curious what’s “normal” out there. This seems a little high (attached photo). Thanks!! 1978 FJ40

I'm aware that this is a common issue but even with all the forums on the 120 series I can't find anyone who actually have specs on what smd led will solder in to my burnt out gauge cluster behind the 0 - 20 mph area.. Help!!! I know I'm only one among many who need to fix their burned out gauge...

Hey there, I recently got an Issopro EV2 EGT gauge for Christmas and was wondering where the best place to put it would be for accuracy and response time? The 2 places I'm deciding against I have marked in red and orange as you can see. So which would be better, or is there another better place...