differential

Hi All, I dont do off-roading and also have not used DIFF LOCK feature much. My 4WD gear setting is also on H as normal, never changed. Toyota changed diff and transfer case oil about 5 years ago. Might do it again this year. Few weeks back i locked the diff while in parking and started...

1986 hj75 troopy wreck. Beginning to approach differential study. What would cause these sorts of scars on the crown wheel please? The scars run most way round. I think it needs at least a new crown and bearings, seal? I imagine pinions are replaced the same time as crowns, they seem to...

Can anyone use these things before I recycle them? They're from a non factory locked 1996 80 series. They're yours for the cost of shipping.

Welcome to our 14th annual DIFFTOBER Sales Event! Save 10 to 13% on over 180 Differential-related products all month long If you are looking for installation services on these or other items we sell, be sure to give us a call! Fully-built & warrantied Differential Assemblies Find the perfect...

From a truck I parted out. The ring and pinion inside are damaged. I am not sure the condition of the differential but I believe it to be serviceable. Bearings are good probably could use some new seals. $200 + shipping.

I told my mechanic to change my differential oil. He inspected it and "saw there was no water in it" and told me it's a waste of money to replace it. He told me if it was his vehicle, he wouldn't do it. I asked him how often he recommends I replace it then and he said every 30k to 40k miles...

Hi, I replaced an old hose - see picture (Differential Pressure Control PN 95337-06020), with standard fuel hose (NBR/PVC SAE30R7). Should I be worried about it? Does this hose require higher standards? Thank you!

I’m looking for one like this in good working order. I can prob just throw a speedy sleeve on mine but would like to do it right if possible. This a course spline with 8mm bolt holes. Here’s what I’m looking for .

I recently tried to tighten up these loose fasteners (the nuts seemed to almost be unthreaded) at the bottom of my front differential. Now they are weeping gear oil. Are the nuts just screwed to studs that are threaded into the axle housing? Or are they some kind of special fastener? If I...

I always thought the differentials and gear cases (transfer excluded) were indestructible.. is it normal a 40 rear differential can get so much wear the teeth will break?

Hi all, First post from a new member. New to me 2006 GX470 cv axle has a loose connection at the input to the front differential. I had thought this would be an opportunity to upgrade to a bushing but a bit a question to ECGS revealed to me that these rigs do not use the pesky needle...

Any thoughts on how this looks? I just placed an oem seal in there. But want to make sure the output flange is good.

I pulled my rear diff lock motor and I mangled the heads of two of the Elocker motor bolts trying to remove them. I think they’re a 90105-08114. Can anyone confirm the part number or recommend an alternative? 1996 fzj80. This is them and where they go. Thanks!

Ok so I have a issue at hand. -------- Solved - Turned out to be a bad Caliper piston that was rubbing on the rotor. I replaced the rear rotors, pads on both wheels, did a little bit of brake bleeding. That fixed the problem. I did put in a brake noise shim this time so I know if my brakes pads...

Replacing rear diff seal. Part number shows 90311-38028 in my parts book. I have one of those seals but it looks different from what is on mine. First picture is before I remove. 2nd picture is of the part I have. Can anyone tell me if this is correct part? I thought it was leaking but looking...

Replacing rear diff seal. Part number shows 90311-38028 in my parts book. I have one of those seals but it looks different from what is on mine. First picture is before I remove. 2nd picture is of the part I have. Can anyone tell me if this is correct part? I thought it was leaking but...

Brand New unopened Dobinsons Front IFS Diff Drop Kit for Lexus GX470, Toyota Tacoma 4Runner and FJ Cruiser. Kit #: DD59-527K Keeps CV angles at a good working angle Allows for lifts over 2.0" Includes all necessary hardware, including machined spacers and nuts/bolts Compliments Dobinsons 3"...

Trying to reinstall everything from the transfer case to the front wheels. I've had virtually no success finding torque specs for the GX470 specifically. I'm convinced I'm looking in the wrong places because I cannot find this information anywhere and I cannot be the only person to ever ask...

Looking for a FJ40 OEM Front Axle Differential - Third Member I can't believe how many of these i have given away or thrown away and now I need one. Hoping to find one in the San Diego area if possible. Pic for visual of what I am looking for.

Hey kids, I have three rebuildable FJ25 long nose diffs that I found in my stash. Gears should be good. $100 ea plus shipping.