bolt

Transmission cross member bolt

I recently bought 2 caps and 2 gears from gamiviti to fix the back/forward operation of my power seats. I successfully got the passenger seat operating again, but snapped the gear for the driver seat while pressing it onto the shaft. I reassembled the seat for now until a new gear arrives. When...

While doing a Timing Belt and Water Pump replacement on my 2002 Land Cruiser over the last week, I snapped both of the long Camshaft Position Sensor bolts while trying to meet the FSM's torque specs. These things were FRAGILE, and now I have a serious bolt extraction problem. The bolts are: P#...

Hi, I'm painting my FJ40 and I thought that I should replace rusted and stripped bolts and screws. I've been looking to get a full bolt kit but I can't make up my mind and have a couple of questions. I've been looking a Metric Overland which I like, but their 1000pc Full Kit Yellow Zinc plated...

Tried to remove by roof rack today - everything went well expect for one bolt on the center leg which had a lot of rust on it. Applied a lot of WD40, and then when I tried to torque out the screw the screw head got destroyed ... and it went downhill from there. I have tried all kinds of things...

$80 for the kit, $20 to pack and ship. PayPal accepted . No PMs. TIA Post or call the shop

Hey guys, Back at again, this time trying to baseline my fuel filter on my '94 FZJ80. So, I went to replace my fuel filter with a new one and noticed it was not bolted in. It is basically just hanging there with the lines.. I guess the PO just gave up when trying to reinstall it. Do you guys...

I'm pretty damn comfortable around tools, but admittedly, this is my first foray into the world of 3/4 drive. Just tightened the crank bolt on the 1FZ to 300+ lbfts. I used the big monster Harbor Freight torque wrench, using a 6pt 30mm socket. Getting the bolt to break free (breaker bar...

Anyone have the alternator mounting bolt size from the F engine handy? I'm guessing M10 x 120mm

I have 2 sets of 4 $75 a set(shipped) located in santa rosa ca . thanks

I noticed that my FJ is pulling left and right when I'm breaking or hit a bump so I took a quick look at the front end and noticed this bolt has broken off. Looks like some grease is leaking out too. Has anyone experienced this? I'm guessing this isn't an easy repair since it's part of the...

I am in need of the phillips screws that hold the bezels on the door in an 82 FJ40, I actually need 4 pieces . I also need the bolt that holds the shoulder harness to the roll bar , mine is stripped. 1982 FJ40

Anyone used one of these on an 80? Part number is 5190935011

SOLD I have a rear GM 14 Bolt for sale with upgraded disc brakes and new armored cover. This was narrowed to fit under an FJ40. It has 3.70 gears in it and is welded. lug bolt pattern is converted to 6 by 5.5 so it fits every 6 lug Toyota. Asking $600 OBO

I'm looking for the bolt sizes for the inner fender, along the edge that bolts upwards towards the outer fender. Also, the bolt size of the ones that connect the piece that goes from the front fender flare to the stock side runners. It looks like it's a unique bolt, similar to the ones that are...

Hi LC Friends- I noticed a couple of days ago my 91 FJ80 tailgate was missing the bolt for attaching the hinge to the tail gate was missing. (Pic below) Upon further investigation, I bought the bolt thinking I could just screw it back in but it seems that nut to screw into is missing. Does...

For the life of me....I can not find this information. I am making a 'holding tool' that will work for both my LX and my 80 series. Apparently the bolt spacing for my LX (100 series) is 65 mm center to center, so I have that info already, but I've read (in my searches) that the bolt spacing is...

Hello. Can't find the specs for the transmission filter torque. In Haynes all it says is transmission oil pan to 61 in lbs. No mention of the filter torque. Chiltons says "Inspect, clean or replace the transmission filter or strainer at this time, if necessary. If the filter is removed, be...

So I was in a hurry (see: being careless) and stripped a nut or bolt on the hub. Should I bite the bullet and buy a hub now or do you think it would be lossy to wait until the next time I take it apart for another brake job or something? It's stripped pretty good and won't tighten or loosen with...