axle

Know where I can find Leaf spring perches for a 93-97 landcruiser rear axle. I plan on swapping a full float onto my mini truck for a camper platform. thoughts, I want your 2c.

I have pulled the rear axle out of my '95 to swap into my '97. It does have the e-locker. I have read in other posts that the axle should be locked when i re build it. True or false? The FSM does not mention this.

Hi Folks, I'm a fairly experienced DIY mechanic getting ready to do a front axle rebuild on a friend's '92 FJ80. Never worked on an FJ or any other solid-axle 4x4. Now, my friend is the sort who does not consider maintaining his vehicle until it needs a repair, so the back plates on both sides...

I've had my '97 for 4 years now and just bought a locked '95. I bought it with the intention of swapping a few parts that I needed to replace on the '97 including an ARB front bumper and the locking axles. So here is where I am... I have installed the locker switch, light bulbs in the dash...

Just a question I am wanting some clarification on. If I were out wheeling and broke a front axle or birfield, could I limp it home or is their risk of the now free axle damaging the tube or other components? I know if I break a rear driveshaft I can engage the CDL and drive home in FWD mode...

I have a complete HJ60 rear axle with the sway bar attached. Will include a picture. Axle is complete, with third and drums still on. Never opened it and I have no use for it. I was going to keep the third as spare but I never wheel hard and I will probably never need it. Gearing may be 3.73:1 I...

I am mid installation of my new 4x4 Labs bumper.......read: I have removed the quarter panel flares and cladding from my LX and the rear bumper cover and mud flaps.... I noticed the axle appears to be off to the passenger side. I have a 2.5 OME and 30mm Slee spacers on it, is this just the...

Was there a known problem with the design or something of the FJ60 calipers from the factory ? The reason I ask is that in my front axle work, initiated by a leaky and seized passenger side caliper, I am finding the driver's side caliper to have seized (but not leak) in the same piston as the...

I am looking for a rear diff or complete axle for a 1991 FJ80. Prefer to pickup some what locally to Portland Oregon area.

Looking for a set of 2 used axle hub flanges for 100 series. Worn flanges are fine.

I've been robbing parts from my uncle's Toyota junkyard. Took the power steering off an '84 for my FJ40 and just brought the front axle home so I can do the disc brake swap. A couple people asked me what I want for it when I'm done. I'm just taking the steering knuckles for the disc brakes, but...

Better start this search now. Anyone with a lead on one? Or point me somewhere? Overseas? I'm in no particular hurry but I want this as my summer project. I'm located in SoCal. Open to freight shipping. Thanks!

I have a crusty rear axle from a LJ70, it should have 4.88 gears in it and is good for parts for someone that owns a LJ series Cruiser and wheels it occasionly to have some spares in case you ever need them. 150$ to get it out of my way

Front axle is sold. I have a front and rear axle from a BJ73 with 4.11 gears in it,these axles are the same with as any 40 series and the only difference is the with of the spring perch mounts. Cleaning up the shop so they are priced cheap to get them out of my way,shipping can be done with...

Everything you see in the pictures- Longfields (30 spline set) 6 Shooter knuckles Steering arms Bearings Trunion eliminators Studs wheel bearings It's pretty much everything you need to beef up your front axle. The Longfields alone are over $600. $900 for everything. Pick up in Las Vegas...

From an early 80's BJ40 Great condition, other than the hard brake line 4.11 gears $500 picked up in Las Vegas, NV, or I can ship via Fastenal

Great condition front axle out of an early 80's BJ40. 4.11 gears and Aisin hubs. No rust. $500 picked up in Las Vegas, NV, or I can ship via Fastenal. Thanks

I need to get some new rear leaf springs. The current ones are 43" long 19.5" from front to mid and then 23.5" from rear to mid. Problem is they are older and since i put the new engine in i am getting crazy axle wrap which has broken/loosened the c clamps for the springs. See exhibit A and B...

I just wrapped up my birf overhaul with the new Aisin hubs on my 97 LX450. I had the 2nd groove machined on my axle and everything went great until I had to put the snap rings on. the new groove and ring seated perfectly but I wasn't sure if I still needed the original clip. The outer...

I have a complete front Axle that came off a 64 fj40. I am asking 200.00 for the whole thing. I am also willing to part it out if anyone is interested in parts. Buyer pays shipping. Located near Los Alamos, NM.