axle

Looking for a set of 2 used axle hub flanges for 100 series. Worn flanges are fine.

I've been robbing parts from my uncle's Toyota junkyard. Took the power steering off an '84 for my FJ40 and just brought the front axle home so I can do the disc brake swap. A couple people asked me what I want for it when I'm done. I'm just taking the steering knuckles for the disc brakes, but...

Better start this search now. Anyone with a lead on one? Or point me somewhere? Overseas? I'm in no particular hurry but I want this as my summer project. I'm located in SoCal. Open to freight shipping. Thanks!

I have a crusty rear axle from a LJ70, it should have 4.88 gears in it and is good for parts for someone that owns a LJ series Cruiser and wheels it occasionly to have some spares in case you ever need them. 150$ to get it out of my way

Front axle is sold. I have a front and rear axle from a BJ73 with 4.11 gears in it,these axles are the same with as any 40 series and the only difference is the with of the spring perch mounts. Cleaning up the shop so they are priced cheap to get them out of my way,shipping can be done with...

Everything you see in the pictures- Longfields (30 spline set) 6 Shooter knuckles Steering arms Bearings Trunion eliminators Studs wheel bearings It's pretty much everything you need to beef up your front axle. The Longfields alone are over $600. $900 for everything. Pick up in Las Vegas...

From an early 80's BJ40 Great condition, other than the hard brake line 4.11 gears $500 picked up in Las Vegas, NV, or I can ship via Fastenal

Great condition front axle out of an early 80's BJ40. 4.11 gears and Aisin hubs. No rust. $500 picked up in Las Vegas, NV, or I can ship via Fastenal. Thanks

I need to get some new rear leaf springs. The current ones are 43" long 19.5" from front to mid and then 23.5" from rear to mid. Problem is they are older and since i put the new engine in i am getting crazy axle wrap which has broken/loosened the c clamps for the springs. See exhibit A and B...

I just wrapped up my birf overhaul with the new Aisin hubs on my 97 LX450. I had the 2nd groove machined on my axle and everything went great until I had to put the snap rings on. the new groove and ring seated perfectly but I wasn't sure if I still needed the original clip. The outer...

I have a complete front Axle that came off a 64 fj40. I am asking 200.00 for the whole thing. I am also willing to part it out if anyone is interested in parts. Buyer pays shipping. Located near Los Alamos, NM.

I have a Suzuki based rock buggy with fj40 axles Under it. The rear has 5.29's and a 12 bolt mini spool and I've broken a few short side shafts so I decided to put some cromo's in. I knew poly performance made shafts for cruisers but haven't looked at them in awhile And it looks like they are...

I am upgrading to a 97 FZJ80 Full Float rear axle so the stock FJ62 axle and spare axle shafts are up for grabs. I have at least one set of spare rear axle shafts (short and long side) plus the entire rear axle complete. Seals and bearings done on rear axle recently. Drives good with no issues...

Took my truck into one of "those" places (4WP) to get ARB's installed in my FJ40 axles. First time ever but wanted to get in on the ARB sale going on for free compressor. It's been in over a week and they can't source "metric axles shims". I feel the need to take a birfield down and introduce...

OK this is really starting to bother me. If I accelerate occasionally (more now than before) there will be a pop from the front left ish. I'm thinking its axle related. It sounds like something is binding then releasing. Then if I brake it will pop again. Last week I had the front drive...

I'm looking for good condition axle shafts, I do not need birfs. If you have a set that does not have a groovy seal area then I'm interested. Thank you

I have a cut and turned front axle setup for shackle reversal in an FJ40. It's been used on a off road truck so it has some dings. Would make a great drop in axle for someone not wanting to cut and turn their own axle. Asking $400 for the housing plus shipping. I am open to offers.

I have a pair of fine spine birfields which have been spares sitting in the back of my garage for 10+ years. I'm concluding I'll never use them, as I have long fields in everything I own. I believe they came out of a 1983 mini truck. In good shape, except for the surface rust on the outside...

Two SS front brake hoses $25 shipped.

Trying to figure out if the axle shafts for the front are different on a 1997 locked vs unlocked.. I have yet to find that they are different but figured someone probably knows and can be a hero! Thanks!