axle

I need a 3sp transfer case for a build i am doing. I am located in Colorado. I also need a FJ40 rear axle.... Thanks, Ben

Our lovely cruiser got rear ended a while back and after fixing and re-aligning the body, the left side goes through a new set of tires pretty quick. I made a thread about this, but never got back to it. Anyone know what the problem may be? Rusty Axle by Elfego posted Sep 24, 2017 at 3:50...

Hi kids, Doing a reseal/bearings on the rear axle (locked) and the RH side axle is stuck about an inch from the hub. And now I can't pull it out,, either! It hangs up about 2 inches from the hub. Can't turn it, can't do nuthin. Have I screwed the pooch here? I've read bunches of threads about...

Bought these a while back when I was doing a SAS. They had just been sandblasted and painted and look great. Looking to sell for $100, which is what I paid (includes shipping). Not looking to make a buck here just trying to get my money back.

SoCal $550 including brakes, drag link and tie rod. Still in the car. Car will be on Jackstands. You will be pulling it. NO shipping. You can have the lower control arms too! I am not parting this axle out. If you need front parts, I also have the following: Hubs, Spindles, Axle Shafts...

Please Delete.

SoCal Pulled the third out and it is in another car now. If you need spare parts, shafts, brake drums, or whatever, send me a message. I can usually ship same day.

I have been (and still am) looking for a genuine Toyota rear axle vent, it is the longer one that also holds the brake line tee to the axle also. I was also wanting to extend the vent instead of having it right on top of the axle, so I was also looking for one of these: No luck so far, so...

Changed plans so now have this for sale. Brand new Trail gear 8" Rock Assault housing with optional inspection hole, E-locker mod, and stud eliminator kit. Has the optional truss kit with it as well. Never been installed from the TG website: Axle housing: $441.03 Extra hole $79 Rear Truss...

Is there a YouTube Video or write-up on how to take apart the hub and inspect the bearings? I found one video where the guy already has the hub taken apart. I'm not even sure how to get to that point. In the picture below, the nuts labeled "A" and "B" that I un-tighten are just spinning freely...

Hi everyone my 97 lx450 does not want to move when the wheels are turned and feels like something is wrong with the front axles, but when the steering wheel is straight car moves fine, thanks in advance and any help will be appreciated

My truck came from Virginia, and Michigan before that with lackluster maintenance history. I am rebuilding the front axles now and am stuck trying to decide what I should I do about these pitted swivel balls. I cleaned them up the best I could and used some rust converter on them. I am trying...

I'm in the process of rebuilding my front axle and this is the CV from the driver's side. The bearings looked fine. Note the wear in the inside of the birf; the areas that looks polished vs. those that don't, similar wear in the cage. Note the wear on the fins of the star, each of the fins...

I'm going to be starting my axle rebuild tonight and ran into another FJ80 owner who said something about rebuilding the actual birf's. I'm planning on removing the axle from the birf and cleaning the old grease out (haven't determined if I'll need to tear apart the birf for cleaning). The...

SoCal Send Personal message for requests and prices.

Im doing a regear on an early fj40 axle (1975 build date) and the axle has a wilwood disc brake conversion. Since the front end is apart I replaced the knuckle bearings and the inner axle seals. Went to replace the wheel bearings but cant seem to get the correct bearing for the inner hub. The...

Need a FJ80 rear axle to finish my build. Ideally looking for a full floater with disk brakes. Don't need the 3rd member if it makes any difference. Located in Sacramento, CA area

Sold

I have some random axle parts from a '85 Toyota Minitruck and a '71 Toyota FJ40. I'm open to offers and parting out. $50.00 + shipping - '85 Minitruck inner axle shafts (long and short sides, no birfields) $80.00 - '85 Minitruck Front Axle Housing (includes 4.11 third member, spring perches...

I have a centered rear axle housing from a 1963 FJ40 that I want to use to build a full float axle. I started a build thread in the hard core section if you want to know more. I am posting in this section because I have one question that I thought could be better answered here. Question is...