Search results for query: *

Forum search Google search

  1. H

    EDIC and Overinjection...

    Thank you for the post guys. We found out the source of the problem. After checking the continuity of each of the wires and the fuel control relay. We discovered it was a bad ground. It is always the simplest things. I didnt even know where the ground for the EDIC was located. (mine is on the...
  2. H

    EDIC and Overinjection...

    Thanks guys, What is the over injection magnet? Is that something on different models?
  3. H

    EDIC and Overinjection...

    I am trying to trouble shoot my 78 BJ40 that is 24v. My trouble is that the EDIC motor does not move and it is stuck in the stop position. I have trouble shot the Fuel Control Relay and it appears to be fine in accordance with the FSM. The fuses are in check and the vehicle starts fine if I...
  4. H

    Builds 1978 BJ40 buildup broadcast...

    Back from leave.... Hey guys...been gone for a long time back for a few days of leave from my latest tour in Iraq. Spent a lot of my time up north with the family but got a couple hrs tonight in on my cruiser after spending some time cleaning the garage :D I was working alone and trying...
  5. H

    Builds 3 days and 3300 miles later

    yeah i will do that once i get settled....everyone likes some good action photos haha
  6. H

    Builds 3 days and 3300 miles later

    lookin' good
  7. H

    Builds 1978 BJ40 buildup broadcast...

    I should have mentioned the real reason behind the square tube under the tub, It was put there as a safety precaution. Its believed that the reenforced tub would provide enough support in the event of an accident but the builders of the tub wanted a no b.s. system in place in the event of...
  8. H

    Builds 1978 BJ40 buildup broadcast...

    Ahhh....yes I am very familiar with that cruiser and the guy who rebuilt it...it's the same method that I used exactly. Travis....sorry about the confusion
  9. H

    Builds 1978 BJ40 buildup broadcast...

    subframe rails JJS thank you, I am not sure that I know what you are refering to with the subframe rail? I set mine up the same way a buddy of mine had. It was straight frame to poly to tub. There is reenforced spots on the tub for the mounts though... Travis
  10. H

    Builds 1978 BJ40 buildup broadcast...

    thank you thanks guys, i appreciate that.... travis
  11. H

    Builds 1978 BJ40 buildup broadcast...

    anyone? does anyone have a picture of the strikeplate that goes on the tub for these half ambulance doors? travis
  12. H

    Builds 1978 BJ40 buildup broadcast...

    half ambulance doors Got back from flying from Georgia to Arizona....now its back to working on the LC. Today I put the half ambulance doors on. Only have one pic to show. Tomorrow I will try and take a pic of the lock pin on the inside of the door. I had to cut it off and will be...
  13. H

    BJ42 windshield wiper motor vs BJ40

    Hello, Can anyone tell me if the bj42 24v wiper motor and rear heater motor are interchangeable with the bj40? Thanks
  14. H

    Builds 1978 BJ40 buildup broadcast...

    thank thanks
  15. H

    Builds 1978 BJ40 buildup broadcast...

    Going to be gone for a month....might post a pic or two tonight but will get back on it when I get back in Feb.
  16. H

    Builds 1978 BJ40 buildup broadcast...

    bracket Never got a measurement on the spacing for the windshield but but went with what I thought was going to work. Made the aluminum back plate that goes inside the tub to help brace the windshield bracket. Went ahead and attached the bracket so....windshield is now attached aside from the...
  17. H

    24V Heater motor/24V windshield wiper motor

    Just PM'ed you. Thanks :)
  18. H

    Builds 1978 BJ40 buildup broadcast...

    Need a measurement from anyone... I got the brackets off the old firewall this morning and working on the windshield right now. What I am looking for is the spacing between the front edge of the tub (or the first lip) and the bottom of the windshield? I attached a photo to maybe help illustrate.
  19. H

    24V Heater motor/24V windshield wiper motor

    Looking for 24V Heater motor/24V windshield wiper motor for my 1978 BJ40. PM me please Thanks, Travis
  20. H

    Builds 1978 BJ40 buildup broadcast...

    Take it off... Today I got did some driving around. I went to a local scrap yard and picked up some scrap metal for the seats bracket. I also made it to a local auto paint supplier who had a long sanding block and 40grit adhesive paper. I used this to wear off the uneven portions of the...
Back
Top Bottom