Could someone tell me what model years the nylon gear (72751-39020) in the tailgate regulator works in?
I have an FJ55 manufactured November 1975. It has front disc brakes so I believe it is considered a '76.
Anyway, I have the gear and want to know if it will work in my year.
SOLD!!!
I am selling my Smurf Blue 1976 Toyota Land Cruiser FJ55 (it does have front disc brakes).
As you can see, it is in poor condition and needing someone to love it back to health. She ran before I pulled the carb to get it rebuilt (Mark's Off Road) but has been sitting around for more...
SOLD!!!!
Up for sale is a new, OEM FJ55 windshield and new SOR seal. I am asking $425 for the set.
I prefer someone to pick it up local (Salt Lake City, UT area) but am willing to try and ship it if the buyer is willing to pay for any packaging and shipping costs. If shipping is desired, I...
I am trying to trouble shoot an idle issue that I am having with my '96 LX450.
For testing the IAC Valve the FSM states, "Using an ohmmeter, measure the resistance between the terminals (B1-S1 and S3, B2-S2 and S4). Resistance: At Cold: -10 -50 degrees C (-50 - 122 degrees F): 15 - 25 Ohms...
While trying to trouble shoot an issue, I came to the point where I needed to check the resistance of the MAF sensor between the THA and E2 terminals.
If I check using my multimeter (Fluke 8062A) in standard ohm measurement mode, I get a reading of non-continuity.
However, if I check the...
I have installed a brand new oil pan and it has a tiny drain plug (maybe 12 or 13mm) . I can't seem to find a part number for the appropriate drain plug gasket on either toyodiy.com or toyotapartszone.com. They only list 18mm and 25mm drain plug gaskets, which I already have and do not fit...
Could someone post up a pick of the location of the charcoal cannister on an '81 - '83 FJ40?
Vehicle was de-smogged (including the removal of the charcoal canister) and I am trying to re-smog in order to register it.
I know that it goes on the PS front fender well but I believe that my FJ40...
I did a search but didn't really find anything that clearly explained the difference and how to tell if I have a full or semi-floating rear axle on my '82 FJ40.
Can anyone point me in the right direction?
I am attempting to install the rats nest below into my '82 FJ40. I have the FSM but it doesn't do a good job of showing me how the various parts attach to the vehicle (i.e. position on fenders, engine, etc.).
I was hoping that a few of you could supply some pictures of your '81 to '83 set-ups...
I noticed that my warm air pull-knob in my dash wasn't pulling out as far as I think it should. I went and checked the Heater Control Valve to see how far it was moving by use of the warm air pull-knob and found it not to be moving the valve as far as it should. I tried to adjust the cable...
Gentlemen,
I have an '82 FJ40. The PO de-smogged it and installed a Saginaw PS setup.
Since I live in Utah, I am re-smogging the vehicle in order to get it to pass emissions. I purchased a Dorry Bracket from Georg in order to free up the smog pump bracket for the smog pump reinstall...
I have looked in both my Haynes and Toyota FSM and cannot find the torques spec for the engine side cover.
I would assume it would be similar to the oil pan (~7 lb-ft). But I would like to know for certain.
Anyone know for certain?
I have the typical leak in my oil pan caused by cracks in the welds where the protective plate attaches to the bottom of the pan.
I have no experience with welding but has anyone every tried to just weld around the entire circumference of interface of the protective plate and the pan itself?
I...
I have a brand new, never used Mark Algazy (marksoffroad.net) rebuilt carburetor from a 1976 FJ55 for sale.
I am asking $300 + shipping for it.
The rebuild itself is ~$300, so you are coming out ahead since you will have a spare carburetor.
Also, you won't have to wait for the time it takes...
I have one of SOR's stainless steel heat riser insulators for sale. Fits 2F's from 1/75 to 8/87.
I am asking $20 for it (shipping included).
PM me if you are interested.