Hey yall,
I'm out of ideas here - I've replaced the relay in the driver footwell, the control box on top of the a/c Box, and the relay thingy on the bottom side of the a/c box. Still, I can't get but low speed on my fan. What else can I try? North American 94 fzj80
Its cold, and I'd like to get a head start on installing my ARB compressor on the QPM without having to actually work on this part outside. Does anyone have a diagram of where to drill holes in the wood? any modifications you had to make to get it to fit, etc?
Hi Folks,
I am letting go of my 3rd row seats - if anyone would like them, I am in the DC area (Alexandria). Excellent condition, the only fault I can see is the seatbelts imprinted into the foam from age. Message for details, info, pickup etc :)
Hey y'all,
I've got a bad U joint and I'm looking for recommendations on a driveline shop near Alexandria that I can just take the shaft itself to and have them rebuild it with new joints. Thank you!
Hi Y'all,
I'm planning out my air system rework and curious how/if anyone who put their air compressor on a QPM dealt with cooling. I found a few older threads but nothing that quite got to what I'm looking for. So, if you happen to be in that category, did you:
Put the interior panel back on...
I still have no idea how any of these VA inspections work - since I'm over 25 years, I think I don't have to do an emissions inspection, but I do have a CEL (I just really don't wanna replace my VSV until its above 70 again lol) and I need to get the safety inspection done before I get...
Hey all,
It's front axle time again for me, but my apartment doesn't allow work this significant :(
Does anyone know of shop space (or any flat, ideally shaded surface) that can be rented by the day? I'm in Herndon these days, so ideally close to that.
Anyone know where to get one that will fit? This is for the screws that hold the turn signal housing to the bumper. My threads have rusted to where they won't engage to back the screw out :(
Hey all, I'm moving to DC soon and my FZ has had a knock for some time, so I'm debating leaving it here with my parents or taking it. If I get there and it feels like it's on its last legs I'd like to ideally have a manual/diesel swap done, or at least a refreshed FZ. Are there shops of that...
Lately, I've been hearing this squealing from underneath the car (like running over a bunch of dog toys). I tried greasing the driveshafts but if anything it maybe made it louder. It also ONLY happens in gear and below about 5-10 mph, if I pop it into neutral ithe sound stops entirely, and once...
Has anyone made or found a solution for the disintegrating places in the door panel meant to hold the plastic clips? I've got several places where I can't get my panels to stick down because the panel won't hold the clips.
Anyone add LED turn signals to their truck? I want to add them on my bumpers for idiots in traffic to know that I'm trying to get over. What flasher should I use to replace the stock one? If I'm using an electronic flasher do I need the factory signals to be LED bulbs too or will regular bulbs...
Trying to find a gauge or adapter set up to get a hard reading on my oil pressure. Hearing waaay more lifter noise at start and while running so I want to ease my fears. What do I need to get?
Hey guys,
Been all over google and mud but can't find any instructions for this. is there a writeup I just can't find? I've got a good deal of mechanic experience so I think I can accomplish this, any advice or warnings appreciated. Was thinking of using this from cruiser parts. Is that really...
Went through some deep (hood height) water with suspended red clay mud over the weekend. ended up with my radiator and oil cooler covered in mud. Since then, I've had this weird thing where when the oil and engine are at environment temps, the pressure gauge reads normal (shoots up to the second...
Have a pair of gently used OME 864s (thick ones in the picture). A little scuffy but still years left in them. Looking to trade down to 863's (we just pay our own shipping) or 100 OBO. Location is GA.
Has anyone installed a viper remote start system? I'll be putting mine in this weekend and it would be nice to know ahead of time where to find the horn, parking light, ignition, door lock and other wires I'll need.
Has anyone else had this problem? My cruise control light stays on, but acts like i pulled the switch back to coast if I use a turn signal, and won't let me reset the speed as long as its flashing. Do I need a new switch cluster or is this maybe something mechanical?
http://shop.cruiserparts.net/index.php?main_page=product_info&cPath=6_29_199_203&products_id=2270
I have one of this style of hood ornaments on the way, could anyone with one already installed give me a measurement from the hood lip to the center of the hole that the mounting stud goes into?
Thanks!