I am looking for a rear semi float long side (driver's side, LH) axle shaft for my 84 FJ60. Needs to have good bearing and seal surfaces as I just found out when changing bearings that I already have one that does not.
Thanks.
As part of the tub swap/complete 2F rebuild, and more for my (mostly) 78 40 series, I finally bought and built the Orion transfer case that I have lusted after for years. The "4 speed case with 3 speed gears" was tired and noisy, and was depositing a good bit of metal in the gear oil.
Ands as...
2006 LX470 Mica gray with gray interior. 194K miles. Extensive maintenance history including new tranny at 184K, new AHC globes and rear springs w/ spacers, and MetalTech sliders.
$19,750
Purchased by us with 181K from 92AZLX here on MUD for wife's DD and to pull a SoCal teardrop Krawler...
New to me 100 series purchased on MUD for wife's DD and tow rig for the teardrop trailer.
Vaulting headlong, with trepidation, into the 2000's and all of the tech challenges that go with it.
I have a Lock Right locker for sale. $150.00 shipped usps
It was in the rear of my FJ40. When I took the almost new Aussie out of the front to install the ARB selectable, I decided to pull the existing rear lunchbox locker out and replace it with the known (nearly new) Aussie.
This is the...
I have an 84 fj60 with slcfj62's harness and H4 housings.
I had one of the harness relays wired to come on with the stock high beam switch and would like to add lights to make this happen.
What would you guys recommend as far as a light choice for this scenario? Keeping in mind that I would...
I wonder if anyone has a 8274 parts winch with a good cluster gear "shaft" gear- the one that rides on the shaft and needle bearings in the upper housing. Mine is completely cracked longitudinally.
Thanks
So, I put the 40 onto the windshield/roll bar after making an (obviously, in hindsight) bad route choice on the Hole in the Rock trail- which leads me to this post. Just the frame, everything else is OK.
Thanks, shipping is to 81631
I am looking for the splash guard that is located underneath the gas fill tube in the rear passenger side fender of a 60/62 series. It is the one that protects all the gas/vapor related hoses That go from the gas tank to the bulkhead fitting. Surface rust is expected, but no cancer, please.
Thanks.
I need one set of 3FE exhaust manifolds in good useable condition to replace the thermonuclear heat producing header currently (briefly) installed. The intake manifold is off of a 1988 FJ 62.
Thanks
I need the main accelerator cable (pedal to the throttle body) for a fj62 3FE. Mine is fraying badly.
Good condition, no major rust or any fraying.
Thanks
I need a 4/85 and later shift guide for the transfer case linkage assembly. In the process of getting parts for the 2FE/ H55 swap, I seem to have misplaced or not gotten the guide to go with the rest of the later linkage parts I have. To be clear (I hope) the part is the stamped metal brace with...
After rebuilding the split case and mating it to new H55f a little over a year ago, I finally managed to install it in the 60 this week. Then, with my keen powers of observation, I noticed a threaded bolt hole on the tranny driver's side level with, and about one inch in front of the fill hole ...
I need the throttle body link wheel (where the throttle cable attaches to the TB) for my 2FE build. It was missing from the donor 3FE motor. If this requires me to buy the entire TB, so be it. Either 62 or 80 series will work.
I need a new or used Downey 4" lift rear leaf spring to rob a leaf out of to replace the busted leaf that I have (in lieu of a new suspension-the lift is less than 5 years old and just broken in -no pun intended.)