i was torqing up the 6 bolts that hold the pressure plate to the flywheel, i got to the last bolt and....SNAP
Question.... is it still ok to drive my FJ62 with this bolt missing for a short period of time, while i source an angle drill ?
i do not want to remove the g/box etc..... just to do...
H55F gearbox swap help info needed
ok... in my FJ62 3F cruiser, H55F, the idler is measured at 34mm.
I am looking at buying a H55F that is a later model with the 38mm idler (complete g/box and transfer).
the question i have... will the complete gearbox and transfer just bolt straight in as a...
is there any internal differances between the 2 tanks?
i removed my standard pertrol tank for my FJ60, and replaced it with a tank from a HJ60.
After 150km of driving after swap, seems i have bad vapor lock.
drove the rest of the way home with fuel cap loose.
Is it the Tank causing the...
A good friend of mine has snapped his LH CV, his cruiser is still sitting just outside the 4x4 park where he did it.
Anyway, a long shot question.
Will a 78mod 45 series CV fit an 88mod 75 series?
i beleive it wont but a secon opinion is always helpfull.
It also runs stock/factory diff...
Hi all, i have a busted transfer case. i have an old 1978 FJ45 4spd manual in the shed, will the transfer case from this fit and work on a H55F g/box on my 1985 fj62?
Cheers - Dave
I think i have a blockage in the main body of my carby.
there is a groove on the under side of the body that directs flow to both sides of the chamber through 2 small holes. how small are these holes suposed to be? as the one on the right hand side of the picture is the blocked one.
how is...
So i picked up a carby rebuild ket for my 3F, in the kit is all the gaskets, the plunger, plunger boot, retaining cooter pins, washers/seals, power valve.
BUT.... shouldn't the kit have included the all the jets (primary, secondry mains, primary secondry slow, power valve jet, bypass jet...
Aussie 3F engine, running rich
I read alot abot hose blockages, so i am looking at them 1 by 1.
in this picture, this hose is blocked by a ball bearing.
why would one place a ball bearing in there?
what does this hose actually do?
I have spark on plugs/leads 2 4 and 6.:bang:
so far i have replaced all 6 plugs, leads, dizzy cap and rotar.
It runs very very rough
Now the killer question, when i apply a little bit of preasure on the distributor body, towards the engine, the other 3 get spark, and the engine...
Is there a code with-in my engine number, or some other tell-tail sign that my engine should be run using leaded, or unleaded fuel?
The filler neck, is a large hole, which makes me suspect it could be leaded, also no sticker at the filler neck specifying unleaded.
Any help would be...
I have read a lot of different threads on fixing the horn
In particular the contact pin.
The contact pin was the source of my problem, so the way i went about fixing it was a 20min job.
SOLDER
a quick clean heat and solder.
here are a couple of pics
Hope it may help others.
If you have...
Blackberryr - Dave's 85-FJ62 Seats are in!!
HI all FJ-Dave from Aussie land here.
I have just picked up this 1985 FJ62 for a bargin price.
Most 60's over here are rusted out, but i found a ripper. it only has a couple of pieces of rust around the flares on the rear and inside the back left...
Am I able to use the spring plates from a 70series (be it 70 73 75 etc..) and us it on a 60 series (be it 60 63 etc...) ?
and vice versa 60 to 70? are the shock pins in the same place, etc....
Cheers - Dave
OK, are all 60 series spring plates the same?
Are all 70 series spring...
1978 fj45r-kjq
Hi all I'm from sunny Queensland Aus. and I have a troopy.
1978 FJ45 L/C V.T to be exact.
Here are a couple of pics
One thing I would like to know, from standard, what is the seating capacity? the plate states 3 which is the front seats, but i have 2 bench type seats in the...