This is great information thank you guys.
I took a picture of it, it's very slow leak I don't even notice for brake performance, at least for now.
Red Merle : Yes I'm in rust area, not too far from WI, I'm in SK Canada. The cost for the parts is about $200.
I probably more liking for remove it...
Hello all,
I just found that my 80's Proportioning Valve is leaking. I kind of noticed my brake fluid got low 1/4 inch in this 3 month, I decide to look for potential problem or leak on brake line. What I found is the rubber seal is full of brake fluid inside.
Do I have any other option other...
Hello all. I can't think of what number for front conner light for LC80, is that 1156 or 1157?
To be clarified I'm talking about it for this type of light
First I thought it's 1156, because it's simple light as reverse light. Then I found little info somewhere that it's actually 1157A...
Thank you!
I think I saw Kal Tire in Burnaby and North Vancouver before, I will hit one in local soon.
I need few OEM parts soon, is there a dealer you guys recommended?
Hello all.
I traveled from East coast to Vancouver last week and I need to get tire balance done. I stopped by many tire shop in around city they refused to do since tire size is 35's. They must be somewhere to get done this. I just new to city and trouble to fine a shop. Where is folks in...
I don't run wheel spacer now with 37's with rim has 4.5 back space. MIne is 4 inch lift.
It rub some for rear bumper side even after removed fender and flaps. I made rear adjustable LCA myself and I extended little so it rub some.
It was rub slightly to frame when it's really stuffed...
Damn it! I just throw them away yesterday since my rear bumper arrived from Jason Crusin off road. I didn't think I wanted to use it. I can rescue them tomorrow from dump can.
When I was looking at Jason's page and all of 80 is nicely tack in tires with fender and flaps I was wondering why...
Thank you for info guys.
I 100% sure I have to keep stock fender then. With fender on, I think it will be tires not sticks out with 37's.
I got day light running light kit, but it's not working as suppose to. may be I got defect.:frown:
I like to know how much tire sticks out from fender is allowed inspection in BC Canada?
I had stock fender before, I kind getting like without it now after a month and I'm thinking close a holes or grind off rear bracket finish it all clean. If I do that, no way I can put them back if I need...
Hello all.
I'm looking to use 6mm or 1/4 wheel spacer for 95 LC80. My rear tire inside is little scrub to frame side, but I assume 1 inch spacer is may be too much tire sticks out from fender. I'm thinking give a try but I'm also little worry lug nut are enough to catch thread to hold tires or...
I just replaced original O2 sensors to Denso sensors. Truck runs good and better than before now because front sensor was dirty and rear one was somewhat dirty. However Denso sensors has less holes compare to stock one. I have no idea how much effect less holes but like I said truck runs good...
Work is done.
Well I did it anyway with 9000 series CAT in order to same some space for pipe to over frame.
I think it came out nice and hope it last longer.
CAT is 9000 series normally use for V8 size engine instead of 2 of 6000 series OEM CAT. No check engine light as of today and I will...
Yes I saw your built and really nice, a lot of weld too.
The one you got cat is seems very small more like tiny, is that size really take care of emission not to turn CEL?
My exhaust is so busted now, I want to fix it before season start.
I like to go EMS powered exhaust system if I have enough fund but not right now. I have to work on exhaust since stock one busted too much can't fix any better.
I stopped by one exhaust shop today and they can do over a frame design but they have to put only 1 CAT since need to save same...
You need to check everything, it seems like totally out of spec.
You need to get gear paint to see better view first and also as well as drive side pinion pattern.
Your drive side shows away too much toe contact usually need to increase backlash, however you already have 1/8 play at wheel...