Recent content by Waytec

I have a pretty simple question I hope. Where is the signal relay located on a 76 FJ 40. I don't have one and the book and google is not helping. Thank you

Thank You. But what is the official name for the diff. Ie my jeep had Dana 44s my old truck had Dana 60s. I am new to the older Toyota stuff so please educate me on this. What I have found is it could be called a 10 bolt or 12 bolt is this correct? if so do I open them up and count bolts...

So what would I say to when orderign gears and lockers. I have a toyota ???? Diff front a toyota ???? rear

Good day I have a 76 and a 77 40 series and am building one out of the two. How do I identify them? They both look the same. Google has failed me on helping me lots on Dana’s but nothing on Toyota. Thanks for the help.

So as my other posts have said I am putting a 350 in my 76 40. I am at the point in my collecting of parts to find a set of headers for the project. I have been reading and lots are using the Ram horns. I don't want to do this. I want a set of headmen headers for the better flow. What i need to...

This has probably been asked 100 times buy now but I am going to ask again. I am going a 350 conversion to me FJ-40 I am in need or a rad. Will rescoring the stock rad do the job or do I have to look at getting one of the conversion rads? Thank You

Give Dave a d Eric a call at Broken Axle in Calgary, 1 (403) 237-7706. They Jeep guys but i am trying to convert them.

Thank You I am digging deep on this as well. Bell housing will work. With the Marks kit it uses a Auto flex plate for the starter and then a spacer then the new fly wheel. My concern is will the bolts that holds all this together work going from a SBC 350 to the LS 3,4. I have not seen the kit...

Good Day everyone. I am looking at putting a Chev 6.0L out of a 03 or newer truck into my 76. Can you guys tell me if the bolt patterns are the same as the 350. I have the Marks adapter kit for the 350 floating towards me and am now thinking of making a change of plans of the engines and am...

What is the common though on the fuel tank location in the FJ-40. I am building mine right now that will be getting a 350 and have the opportunity now to easily move the tank to a cell setup in the rear as part of a storage system. or I can wire wheel the ones I have, POR 15 the out side and...

This is the first step. Who knows where this is going to go over the years. I just want to first get it running and out on the road and trail. With the kit they use the advanced adapters bell housing. It dose say I have to have new drive shafts made. Dose it relocate the transmission? I really...

Good day I am looking at the chev 350 swap kit from Cruiser Corps. Has anyone used there kit befor, what if you think of it and what extras do I need to make it all work. Thank you

Right now it is on 35s, and 38 pitbulls will fit witch are like running a 40 for wight and abuse to the drive train. Right now it is get it running and moving under its own power. Then each year go after somthing biger on it. In the end it will be on D60s 3 link fromt 4 link rear with a v8 in...

I am going hard core with this rig. In my mind i am stating with a cool tub, frame and vin number. I just had a friend of a friend call me with a 4.3 (a 350 that is missing 2 pistons) for please bring beer. I am thinking this an good option for now. To get me running and driving. I will put the...

Hey everyone I posted once looking for places to find parts and derped it up pretty good. So i will try this again. I am looking for some advice. The engine I have in my truck lived under water for a little bit in the Calgary floods. Looking in the oil fill hole and card it looks pretty...