Recent content by tristanbh

  1. tristanbh

    Throttle Body Cleaned, APPS replaced, now non stop clicking/popping sound

    Looking for some advice. Have a 2000 LC with 198k. Two weeks ago on a cold day the CEL & VSC Trac On/Off came on, truck went into limp mode and I got a P1120 code. Issue went away on a warmer day, and my thought was the throttle body needed cleaning or a new APPS sensor. Cleaned the throttle...
  2. tristanbh

    100 Series Attic Shelf Bracket Availability

    I'd like to put my name down for a set as well.
  3. tristanbh

    Rear spoiler bolts

    I'm not sure how standard the diameter of the rivnuts are since the spoilers got installed as an option, but luckily the diameter was a bit smaller than the new ones I put in, still used an M6 rivnut though. These are the ones I used: McMaster-Carr - https://www.mcmaster.com/97467A666/ I was...
  4. tristanbh

    Rear spoiler bolts

    Had a branch come down on my spoiler a few weeks ago cracked both the mounting portion on the underside of the spoiler as well as the passenger side mount itself. Plastic seems super brittle. Luckily I was able to tighten three of the bolts down fairly well after removing the plastic mounts, I...
  5. tristanbh

    Noise after exhaust work

    I’m taking it in on Tuesday to get it checked out, as bad as it sounds in the videos it has been driving great, though I’ve been limiting how much it’s getting driven. I did notice one of the bolt points in the splash guard broke off, thought that had to be the cause. Maybe some extra vibration...
  6. tristanbh

    Noise after exhaust work

    Thanks for all the input, gonna talk with the shop today. This all definitely helps with where to look.
  7. tristanbh

    Noise after exhaust work

    The clunking sound from bumps in the video above and what you’ll hear when I’m giving it gas in the video below seem to correlate. Checked all the exhaust clamps, nothing seems loose there, I was worried about the head gasket, but nothing is leaking. New O2 sensors up front. No CEL. Here’s the...
  8. tristanbh

    Noise after exhaust work

    Yeah that’s what I figured the heat shields would sound like, just couldn’t find an example of it. My symptoms seemed to align with what people were reporting for heat shield rattling, that’s why I thought it could be that. I have no idea what could be making the noise, I got under the truck...
  9. tristanbh

    Noise after exhaust work

    Hey there, Yesterday picked up the truck after getting DT headers and cat back exhaust installed, I’ve got this rattling noise that showed up right after. Noticeable at low speed bumps but also increases with rpm. Seems to eminate from the underside, slightly forward from driver seat, and...
  10. tristanbh

    ARCHIVE Wits’ End Fire Extinguisher Mount and Locking Lid

    This looks awesome, I’m in as well.
  11. tristanbh

    Another rust question

    yeah looks like that snorkel thing sprays 360 too, should make it easier spraying the inside, thanks for the tip.
  12. tristanbh

    Another rust question

    Thanks, that’s good to hear. I know rust is the bane of existence around here and I really thought I had thoroughly checked it out. I’ll be getting some fluid film and do as you suggested, thanks again.
  13. tristanbh

    Another rust question

    I know this stuff has been covered, and I apologize for my ignorance ahead of time. I’m trying to get a little perspective on the situation. I purchased this 2000 a couple weeks ago from another member, after saving and wanting a Cruiser for a long time. Checked it out during the purchase and...
  14. tristanbh

    Took the plunge!

    Thanks that’s definitley a place to start, no trouble codes were captured by my OBD-II. Thanks for the input.
  15. New Rig

    New Rig

    Took my new 2000 LC on a shakedown run in GWNF
Back
Top Bottom