Recent content by Rust Bullet

  1. R

    Spraying Rust Bullet with an HVLP gun...

    Spray Rust Bullet Automotive When applying with an HVLP spray system, use a 1.7 to 2.0 tip at 40-60 psi. Prior to spraying, run Rust Bullet Solvent or Xylene through the spray equipment to remove any moisture that is trapped in the sprayer. After each coat of Rust Bullet is applied, flush the...
  2. R

    Rust Bullet Product Review

    Please note that Rust Bullet was coated over rusted Q-Panels as were most of the other products being tested by these independent labratorys. Some products were not applied over rusted panels because the manufactures directions specifically stated they must be applied over clean metal...
  3. R

    How much Rust Bullet?

    I'd love to have a few pics too :)
  4. R

    If I paint with epoxy primer.......

    We have had only one issue with painting over Rust Bullet. This involved using an asitone base Rust-oleum paint. Any paints containing acids, oils base, will not stick to Rust Bullet. Any Laq. primer or etching primer should adhire just fine. After the 36-48 hours cure time of Rust Bullet you...
  5. R

    Rust Bullet Product Review

    Correct, Unless your working on a surface you plan to do cosmetic or wish to have a very smooth surface for finishing and plan to lay laquar over it. If you plan to use on body panels etc, I'd lay down a couple of coats of primer on top of RUST bULLET so you can wet sand and get the finish you...
  6. R

    Rust Bullet Product Review

    Noted... May be kinda hard to get the 55 Gallon drum to travel down the track with crash dummies riding it ... but...
  7. R

    Rust Bullet Product Review

    Such a system was in the past test samples. The test subject was the Wasser Brand Systems Panel. Wasser is most known for such projects as painting the Golden Gate Bridge, Manhattan Bridge as well as other large projects This consisted of the following applications MC Miozinc - moisture-cure...
  8. R

    Rust Bullet Product Review

    Wrong :) Try this test.. take a bolt and nut and screw then togeather. Coat with Rust Bullet and let cure.. Give it a week and then try to remove the nut..:) Hope you have a big wrench.. if the nuts and case had any rust at all the bores of the metal are open more. This gives Rust Bullet a good...
  9. R

    Rust Bullet Product Review

    Really depends on the surface. By nature Aluminum has a very smooth surface and has little to bond to. Brushed aluminum may be better as it's not polished. Raw aluminum would be fine. This gives me an idea for other testing.. Glad you brought it up. I'll see if we can get various metals with...
  10. R

    Rust Bullet Product Review

    The problem we are expecting with rusty panels is giving an *even* test. You can't control rust and how it effects metal. We can surly test on a seasoned surface but I'll BEAT YOu once we do, one of the product reps tested are going to come back with " You used a worse panel on ours" so it will...
  11. R

    Rust Bullet Product Review

    Not as of yet, still setting up dealers and Distubutors. We've have 4 come online this week and more are scheduled.
  12. R

    Rust Bullet Product Review

    Most of the test preformed were requested my the Navy. Certain testing has to be done before any product can get approvel for use aboard Navy ships. the same is for pretty much any goverment location. The standards they use for testing are the ASTM testing. ALmost every company in the field use...
  13. R

    Rust Bullet Product Review

    Im not sure I see your connection. The test were performed to give an even chance to the other products in the test for "rust protection". The majority of the customers we have do not have a rust problem and are trying to prevent rust from forming as long as they can. Of the 8 products test...
  14. R

    Rust Bullet Product Review

    You did clean the frame good with at least soap and water to get the loose rust off right ? Just checking. :)
  15. R

    Rust Bullet Product Review

    On that note if you have any questions, please ask now. as I'll be out of town till next friday at the trade show and will not be avilable for questions till then.
Back
Top Bottom