98 SNAKE EATER

Threw my order in this morning, was going to do local pickup but figured it would cost me more than $10 gas to get there and back. :)

I finally installed mine last week. Shipping was fast, packaging was excellent, instructions were great, installation was easy. I had my seats out for another project but removal is not necessary at all. Windows now work like a modern car...

When cleaning, I use a few small zip ties to hold the brushes in place, then just blow everything out with compressed air

Done it plenty of times I just leave the socket in to hold the brushes and let the armature push it out of the inspection hole while lowering the endbell into place. All 4 brushes snap onto the comm instantly. Here's a short video on a...

To spin the motor, you only need these two leads for positive and ground The other grounds mentioned are to activate each of the flow solenoids (not necessary when testing just the motor) Keep in mind, if you're bench testing a unit that...

Are you getting a click or a little spark from the wires when touching to positive lead? If so, it may be shorted. The pumps are notorious for shorting out due to rust scale in the endbell. Here's one from a junkyard before and after cleaning...

I bit. So far the product works as advertised. Speed of the windows improved greatly and my passenger rear window, which the po glued into place out of alignment, and has always stuck halfway up, now powers through the bind and goes up first...

Just curious, but anyone try these cheap speed bleeders on Amazon? Tried bleeding mine today and my driver front original bleeder got mangled (had to use a vise grip) Firgured I'd order a set of speed bleeders and this thread popped up while...

I installed my Window Rocket this weekend and it is as advertised. The only bummer is the drivers side regulator binds and takes several attempts to close the window. No fault of the window rocket but did help to reveal the deficiency in that...

Designing products is never boring. I've turned a page in Window Rocket kit development for all non-ABS cruisers and before I toss out all the prototypes and "almost products", I thought it would be interesting to display all the iterations that...

19mm thinwall socket does the trick

Rust is caused by condensation and if someone decides to use a pressure washer on the abs pump. There is a weep hole on the bottom. Most of the ones I've taken apart look like yours except it's not the magnet that gets in the way it's the...

I've seen that too, and nope! Marketing crap for more hits, especially since Heritage 200's are grabbing a premium these days.

I've seen quite a few 80 series listings on FB titled as "Heritage Edition" or "Heritage Edition Sport" :hmm: They all seem to be modified in some way, but I don't see anything regarding the H.E. label :meh: Was this an actual thing for 80's?

Follow-up report -- Successfully repaired. Pulled out all of the vampire taps and the U-Haul adapter in the driver's side wheel well, re-insulated. Still blowing fuses instantly. Upon further inspection from under the vehicle at a somewhat less...

Fabulous product and damn fast delivery!!!! I cannot wait to see how it works come Winter time. Maybe I can get the window up fast enough to prevent getting pneumonia on 20 degree days. This has nothing to do with the Window Rocket and...

Holy extendo!!! 😜 What's your departure angle? 😳😁

Went to the beach on this rainy day

I finally replaced my military terminals with something nicer. New reman Jag 140A alternator installed. Only minor trimming to make it fit.

Been running this for a bit now and it’s a game changer. Maybe my windows will roll back up in the winter again.

I only just discovered this product last night from seeing a post on FB… now I’m convinced I need this in my life! Patiently awaiting the RHD kit for my Aussie 92 GXL

RHD guy's, sorry, you'll have a little longer wait. Test fit our latest non-ABS RHD mounts last night and there's interference with the throttle pedal. This will put me behind a couple weeks past the target of end of this month for releasing the...

one of these got installed on a customer LX450 at my shop this week with stellar results! My staff and I will be recommending them to all 80 series owners going forwards. Great product.

I just installed one. It is great! I replaced window runs, motors, and regulators on my 93 and they are still slow. Also, one of the new regulator gears stripped after a few weeks on a new, Aisin part. On my 94 I installed the Window Rocket...