Reviews for TCC Rear Bumper?

[rlynch356]

No Link you have to Email/Call them - so it takes a bit of effort. (it took me a couple of weeks to get it done and a phone call to them to do the CC)
This is for the US Drivers side, they also make a passenger side kit for the spare tire.

This is in Australian $... btw....

K6314JC-KIT - $136.20 Freight via DHL - $100.00 Total $236.20 AutoPacific Australia Pty Ltd (Hayman Reese/Rola/Kaymar/Thetford) Phone: 1800 812 017 AutoPacific Group PO Box 4397 Dandenong South VIC 3164 Australia kaymarsales@autopac.zendesk.com>

 

[arun1]

View attachment 3701879

Overall, really happy with the fitment and function. Some small aspects could be improved and the correspondence with LRA was great. I'll do a follow-up/detailed post once I get the jerrycan holder installed, lights wired and license plate relocated. I think there's plenty of room to drill a hole in the bumper to relocate the 7pin plug, which I may do later on. I think relocating the reverse camera will be fairly easy as well at a later date.

Looks phenomenal. Did you install it yourself or a shop did it? I am also in the market for one. Thanks for sharing the pictures, would love to see the final install pictures with the spare tire and fuel cans.

 

[kdubbya]

@arun1 I did do the install. Slow rolled it over the week. Was pretty easy actually. Had a few questions along the way but @Astott and another LRA rep were very helpful. I'll get it all wrapped up and post some more pictures. I plan to change a few thing such as the swing arm latching mechanisms and I'll post those changes as well

 

[ExpeditionMan]

@arun1 I did do the install. Slow rolled it over the week. Was pretty easy actually. Had a few questions along the way but @Astott and another LRA rep were very helpful. I'll get it all wrapped up and post some more pictures. I plan to change a few thing such as the swing arm latching mechanisms and I'll post those changes as well

Do you think any part of the bumper would interfere with the AHC pump?

 

[kdubbya]

Do you think any part of the bumper would interfere with the AHC pump?

Can you post a picture of where that's located?

 

[ExpeditionMan]

Can you post a picture of where that's located?

Located behind the rear passenger side tire. Sits at or above the frame.

 

[kdubbya]

Located behind the rear passenger side tire. Sits at or above the frame.

View attachment 3705069

View attachment 3705070

I don't believe it would impact that at all as far as the install goes. I have the 40 gallon LRA tank, installed just before I did the bumper, and it doesn't interfere with all of the tubing and transfer pump in that rear passenger fender/quarter panel area. However, the underside is wide open to the ground currently on my install not sure if this is from me not replacing all the plastic paneling after I did my tank install or just how this setup goes. There is what looks like to be provisions on the bumper that were intended for mud flaps, maybe front or rear install, that could be used to for a protection plate of some kind. I'll post a video and walk you through what it looks like.

 

[kdubbya]

No Link you have to Email/Call them - so it takes a bit of effort. (it took me a couple of weeks to get it done and a phone call to them to do the CC)
This is for the US Drivers side, they also make a passenger side kit for the spare tire.

This is in Australian $... btw....

@rlynch356 you have a picture of the bracket it comes with?

 

[rlynch356]

for the camera?
here you go, pretty simple L- type bracket.. I have it mounted under a propane tank mount at the moment.

 

[kdubbya]

for the camera?
here you go, pretty simple L- type bracket.. I have it mounted under a propane tank mount at the moment.

View attachment 3706509Thanks. I think I could just move the camera with is current bracket to the jerry can holder with my current setup. Then get a camera blanking plate for the old location.

 

[rlynch356]

The Kaymar relocation kit comes with a blanking plate.. and requires no cutting of the harness.

 

[kdubbya]

The Kaymar relocation kit comes with a blanking plate.. and requires no cutting of the harness.

So I reached out about this and they just referred me to www.dreamteamcar.com which isn't in English,Translate is having a hard time with it. Fun

 

[rlynch356]

no idea..but that is the only international one they list... which is not helpful most likely.

this is the contact I used... I used the contact form and just asked to order it and send it DHL

Contact Kaymar​

49-75 Pacific Dr,
Keysborough,
VIC 3173.
Phone: 1300 583 973
Email: sales@kaymar.com.au

 

[ironmountain]

View attachment 3701879

Overall, really happy with the fitment and function. Some small aspects could be improved and the correspondence with LRA was great. I'll do a follow-up/detailed post once I get the jerrycan holder installed, lights wired and license plate relocated. I think there's plenty of room to drill a hole in the bumper to relocate the 7pin plug, which I may do later on. I think relocating the reverse camera will be fairly easy as well at a later date.

I noticed the 200 series bumper being sold in Australia advertises a reinforced carrier and the carrier place is also angled.
The American version is not reinforced and appears to not be angled.
Does anyone out there know any details as to why we get the toned down version?

 

[kdubbya]

@ironmountain did you reach out to long range america? They've been very responsive on all my questions and I'm sure could answer that.

 

[ironmountain]

@ironmountain did you reach out to long range america? They've been very responsive on all my questions and I'm sure could answer that.

Yes. I ended up ordering one from Aidan at LRA. Very helpful along the way. The stated that the upgrades listed above are their newer version that they sell to AUS and USA.

 

[ryanCA]

Yes. I ended up ordering one from Aidan at LRA. Very helpful along the way. The stated that the upgrades listed above are their newer version that they sell to AUS and USA.

View attachment 3807757

need to see your truck in person before ordering!!

 

[ironmountain]

need to see your truck in person before ordering!!

Always. Hit me up! I’m in OC

 

[kdubbya]

Yes. I ended up ordering one from Aidan at LRA. Very helpful along the way. The stated that the upgrades listed above are their newer version that they sell to AUS and USA.

View attachment 3807757

Do you have pictures of the underside of the feeder areas? Mine are wide open.

 

[ironmountain]

Do you have pictures of the underside of the feeder areas? Mine are wide open.

Your fenders are wide open? I don’t understand