parting out F out of a 67 fj40 $5 sale!!! remaining items

[dohcdelsol93]

Had a thread on here earlier where i sold all large componets.

This new thread is all the small stuff that remains

All of it is $5 picked up or mudship

or

$5 + shipping. Until i get my rig back up and running all parts will ship UPS.


I have lots of valve train parts (dropped one valve)

5 good pistons

fuel pump

water pump

pulleys

flywheel

3 finger pressureplate/newer clutch

starter

alternator with bolt broken off on adjuster arm (should be easy to drill out)

oil pan

valve cover

mis. hoses, hard lines

parts for column shift 3 speed (linkages)

tons of hardware

block

head with slight damage done to seat

much much more

as mentioned all parts $5!!!! plus shipping.

Any pics you need hit me up and i'll snap pics.

 

[CRZNLZD]

Might you have a crank pully?

 

[dohcdelsol93]

yes i do.

Has a funky deal on the front of it where it looks like you can hand crank start it.

 

[dohcdelsol93]

anything pictured here except the clutch fork (might need, if i don't use it later this week it's back up for graps)

also not picutured is the 3 speed column linkage and pretty new remanned starter.

 

[CRZNLZD]

Great, I beleave the 'hand crank' on it might be the nut to hold it in place. I have one just like it on mime. Can I get a price for it with shipping to 92307. Also can you post a picture of the crank pully. Thanx.

 

[dohcdelsol93]

I'll pull it as soon as i get done with my water break!
Shipping will be about 17.50 UPS, about 2 bucks cheaper if you a buisness.

 

[CRZNLZD]

Sounds good. Will pm you.

 

[Living in the Past]

The pulley is pressed on and the crack is part of the pulley. Need a puller to get it off.

 

[dohcdelsol93]

thanks bro but my brass drift and a small piece of wood left over from the teak work i did on my sailboat already got it off.

 

[dohcdelsol93]

 

[dohcdelsol93]

engine failed because of dropped valve in cylinder 3 (see pic)

Everything else internally should be good!

 

[rgentry]

Will take 3-speed linkages, oil cap, oil pressure sender, clutch fork and ball, fuel pump and oil pressure regulator. Let me know what the cost plus shipping to Altanta will be. At $5 per that sounds like $35 plus shipping. RG

 

[dohcdelsol93]

i know what the oil pressure sending unit is but what is the oil pressure regulator...spring on oil pump.

i will pm you my number.

 

[rgentry]

I will call tomorrow afternoon. The thing in the red circle is the oil pressure regulator.

i know what the oil pressure sending unit is but what is the oil pressure regulator...spring on oil pump.

i will pm you my number.

 

[dohcdelsol93]

not a problem, thanks for the pic...all yours.


on the clolumn linkage the main shaft that runs the legenth of the of the column, it has an arm no it right by the steering box. this arm had to be cut off because of rust (broken set screw)

The rest is all there but i would replace the pivot ball ends. The PO ran them loose for years.

 

[dohcdelsol93]

Will take 3-speed linkages, oil cap, oil pressure sender, clutch fork and ball, fuel pump and oil pressure regulator. Let me know what the cost plus shipping to Altanta will be. At $5 per that sounds like $35 plus shipping. RG

for the small items your looking about 15 shipped to residenial, about 12 for buisness.

On the linkages in a seperate/longer box about 15 buisness and 17.50 residential.

again on the linkage. This is only the linkage rods and the main arm that runs along the column had to have the little arm cut off for removal, the set screw bolt broke off when trying to remove without cutting apart.


it is just the linkages, not the tranny cover.

I do also have the shifter lever i'll throw in.

 

[dohcdelsol93]

Will take 3-speed linkages, oil cap, oil pressure sender, clutch fork and ball, fuel pump and oil pressure regulator. Let me know what the cost plus shipping to Altanta will be. At $5 per that sounds like $35 plus shipping. RG

all items sold to rgentry pending payment.

guy has not got back to me on crank pulley. Pulled and ready to ship.

 

[dohcdelsol93]

make offer on small parts + shipping!!!!

 

[dohcdelsol93]

the column linkages, oil sensor, regulator, pivotball and clutch fork sold

will be this weekend before i get back to the rig to remove parts.

The wife is having some pregnancy complications.

Don't worry guys i will be out there this sat and/or sunday to remove everything i promised out!!!

 

[dohcdelsol93]

all parts for gentry are packaged and being shipped except for the oil cap and fuel pump.

Those parts will be pulled tonight and shipped tomorrow. (i boxed everything up but knew i was forgetting something) I'll be throwing in an extra 2nd oil cap as well for patiently waiting on me to get his parts out to him.

Carb will be shipped to clemson cruiser tomorrow aswell


Bellhousing has been removed and sell pending on payment/shipping quote.


The wife is doing ok, had a scare where we thought she was going into premature labor but turns out to just be a LOT of pain that they can't explain a reason for. Baby is doing ok.

I'll be pulling/shipping parts as quickly as i can

I purchased a bike to get to/from work while the cruiser is getting put back on the road so transportation on small items is no longer an issue!