teejnut
SILVER Star
- Vehicle Model
- 200 Series
- LX570
Selling my used RLC rear bumper with dual swingouts (tire carrier + triple jerry can holder). I originally bought this mainly to just use as a rear bumper without swingouts but plans have changed and upgraded to a Dissent.
I installed the rear bumper without swingouts on April 2022 and it has been rock solid. I have not had any issues with it. Been to trails in Moab and Ouray and it never has shifted or moved at all. I bought the swingouts since it wasn't that much more but never used them. I did install them to try out and there's an issue with the PS swingout hole for the pin that keeps it open. The location need to be moved or else the lower tailgate won't open. Or one possible solution is to fab up shocks to keep the swingouts open vs the pin. Bumper was spray painted with primer and then bed coating spray.
Bumper works fine with the LX570 and AHC. You can see in the pics how the wing bracket is mounted. And will work for LC 200-series as well.
Below is a picture of the bumper right before I removed it. Here's a link to the album of pics: The bumper is in used but good condition. No bends, dents, bends, etc. Could use a fresh paint. I did drill a hole to mount my trailer plug.
The album includes pics of each step of removal so you should be able to just use the pics for installation. I have bagged/labeled all the bolts and brackets to make it pretty straightforward. I replaced all the RLC bolts with zinc plated ones from McMaster. Will include all the RLC hardware as well which includes extra bearings and dust caps for the spindles.
Mud thread with user feedback/input on the RLC: RLC rear tire carrier / swing out / jerry can / custom fab bumper - https://forum.ih8mud.com/threads/rlc-rear-tire-carrier-swing-out-jerry-can-custom-fab-bumper.871580/
I paid $2,395 shipped. Currently it would be ~$2,545 shipped for the same setup (it was extra for the 2nd swingout). Looking to get $700 but OBO. I'm located in Monrovia, CA 91016 and wouldn't consider shipping at this time. So local pick-up only.
I installed the rear bumper without swingouts on April 2022 and it has been rock solid. I have not had any issues with it. Been to trails in Moab and Ouray and it never has shifted or moved at all. I bought the swingouts since it wasn't that much more but never used them. I did install them to try out and there's an issue with the PS swingout hole for the pin that keeps it open. The location need to be moved or else the lower tailgate won't open. Or one possible solution is to fab up shocks to keep the swingouts open vs the pin. Bumper was spray painted with primer and then bed coating spray.
Bumper works fine with the LX570 and AHC. You can see in the pics how the wing bracket is mounted. And will work for LC 200-series as well.
Below is a picture of the bumper right before I removed it. Here's a link to the album of pics: The bumper is in used but good condition. No bends, dents, bends, etc. Could use a fresh paint. I did drill a hole to mount my trailer plug.
The album includes pics of each step of removal so you should be able to just use the pics for installation. I have bagged/labeled all the bolts and brackets to make it pretty straightforward. I replaced all the RLC bolts with zinc plated ones from McMaster. Will include all the RLC hardware as well which includes extra bearings and dust caps for the spindles.
Mud thread with user feedback/input on the RLC: RLC rear tire carrier / swing out / jerry can / custom fab bumper - https://forum.ih8mud.com/threads/rlc-rear-tire-carrier-swing-out-jerry-can-custom-fab-bumper.871580/
I paid $2,395 shipped. Currently it would be ~$2,545 shipped for the same setup (it was extra for the 2nd swingout). Looking to get $700 but OBO. I'm located in Monrovia, CA 91016 and wouldn't consider shipping at this time. So local pick-up only.
Last edited:
