Wanted FJ60 Manual (39 Viewers)

[Junk]

Depends on how soon you swing through NJ

 

[OGBeno]

Fochdog...

I might be going to NJ in the next month or so...I could pic them up for you and have them at my place in Akron if you'd want to roll down...

Or, you can always get them shipped....

Later.
-o-

 

[fatboy]

https://forum.ih8mud.com/showthread.php?t=49968

240 is a little steep for me

 

[sine80]

mini arms

I needs some mini steering arms to finish my fj40 disk conversion...

 

[ALEXGAR]

Need Rag Joint

Anyone have a rag joint for a "79 steering column?

 

[3pits]

I got them but for a 62 and in NE GA,,,pm me if you want to ship

 

[3pits]

ive got a few sets if NE GA is closer, pm me if you want them

 

[3pits]

I had a lincoln sp 100 (like 10 years ago) and a friend has the 220v version and there is njust no comparison the larger 220v non portable units,

maybe I dont know what thickness mat. you are welding, but in my book I would rather have too much power than not enough,,,, and with a smaller machine you are limiting yourself, the first pass rates as a preheat,,I don't know anyone that is entirely happy with the smaller machines,

 

[Texx]

Still available from Toyota, $54.00.

 

[3pits]

yea, I got one, still in the package, pm me with your email addy

 

[KLF]

Here ya go:

http://www.yankeetoys.org/KLF/ForSale/ItemDetail.cfm?FS_ID=85

 

[mr_manny]

looking for early fj40 door handles/interior latching stuff..

Looking for early fj40 door handles and interior latching mechanism...
thanks,
manny

 

[Got Cruiser?]

89-95 pick-up bed

I am posting this for a friend who is looking for a Toyota pick-up bed from 1989-1995 in good condition. No rust or major dents. Please contact Vern at toyspecialists@attglobal.net or www.toyspecialistsaz.com

 

[clemson55]

I've used setups with gas and with flux core, 110 and 220, with varying wire thicknesses, and probably anything else you can come up with. And I can get nice welds out of my roommates cheap old welder (which is now broke) which I think came from lowes. I mean sure it doesnt compare to a really nice expensive welder with gas like the one I used at the University but they can get the job done if you know how to use them.

 

[cruisers4wdtoy]

Trans.

Looking to trade 2 1975 FJ-40 FRONT DOORS FOR A SM420 OR 465 trans. with the 3 speed transfercase already mounted to the transmission. If i am out of line let me know.

 

[1extrmfj]

rear cross member

I got it. I will take some pictures tonight. Thx. Duffy. What is your Email address? Where are you at? Im in Colorado

 

[sven]

tailight assembly needed

wife waxed my fj62 with her volvo of all things. I'd like to find a used tailight assembly, driver's side lense and all....probably don't need the gasket but all the plastic. Anyone with leads (other than local Toyota) let me know. Thanks.

 

[1extrmfj]

Fan Shroud

I think I have one out of a 1977 fj40. I will Check and see. Where are you at? I am in Colorado. If I have it I wil take some pictures. Thx Duffy Whats your Email address?

 

[Degnol]

email:
Aun2th@aol.com

I'm in Kansas City.


Thanks for checking



Ed

 

[Poser]

Unless they are the late modle doors that have wing windows, and are spotless....you are....



but hey...ya never know.



Good luck!


-Steve