Wanted FJ60 Manual (1 Viewer)

[Landpimp]

the last 5 digits of the part # will tell you the length, pitch and diameter

SOR sells bulk nuts and bolts for land cruisers. They are the gold (cadmium plated with chromate coloring) hardware. SOME of those are Toyota parts, and should be available in bulk, from CDan or your dealer, if you can figure out the parts numbers. The issue is figuring out which are what. (Dan and I are working on some of those now).

It looks to me that the nutsandbolts.com hardware isn't cadmium plated.

 

[e rock]

Bump - still looking for a relatively clean replacement

 

[rtiqulatendisco]

I did a search an found that they are available. The ones for a 450 are of course more than the fr flaps for a 80. You can also make the ones for an 80 fit a 450.

 

[JasonH]

79+ lower knuckle cap

I need one lower knuckle cap for a 79+ Cruiser or minitruck steering knuckle.

 

[LX_TREME]

Oh of course i seen those too (The 80's front mud flaps).By the way, do you have any pics? I want to see how it looks like...Thanks

 

[Cothran]

sm420 front bearing retainer

I'm looking for the front bearing retainer (nosecone) for a late model 420, the one with a seal. Anyone?

-Tim

 

[wngrog]

OK, is this the "radiator" part that goes in front of the radiator? I have one and the littel cylinder that goes under the hood.

 

[orangefj45]

hey tim.
got your email. sorry, but i don't have one except for the one on the trans and i do not want to take a part off a good transmission.

i'd say try pic-n-pull.

 

[78 One owner]

Good info... thank you. The bucket is a good idea.

I actually stored the first one I broke in a bucket until the bucket gave up the ghost.

 

[Rogue]

Flare Needed...

Hey all,

Today I managed to tear the front half of my DS rear flare. Anybody got one laying around?

I was surprised at how much of the hit it absorbed. The body is fine and the flare is intact but cracked. Fiberglass is amazing.

Let me know... Thanks.

 

[mike]

77fj40 running boards

I'm looking for a good solid , rust free set of running boards for a 77fj40. Let me know what you have. Thx

 

[1Fine40]

None available on this board????

 

[wob]

What year?






Nevermind - couldn't see the color in your sig line at first.

 

[NorCalDoug]

Not yet...and you've got some competition too
It might help if you suggested a price range.

 

[Rogue]

All years should mount the same. My flares are line-x'd and this one would need to be as well. The only difference I know of is the material changed to plastic at some point rather than fiberglass.

 

[NorCalDoug]

no...you might want to verify, but I don't think all years are interchangeable.

The 91/92 are fiberglass, but narrower (they don't stick out as much) than the 93/94.
The 95-97 are plastic, rather than fiberglass, and are the same width as the 93/94, but I think the mounting points are different.

 

[NorCalDoug]

Not the best pic, but there's one in this thread.

I'm gonna want a set for the wife's LX once I get the sliders on hers.

 

[Rogue]

Oops. I did know about the 91-92 being different. I thought I remembered the 93-97 being the same except materials. I could be wrong though...

 

[john0089]

Hardtop In Nc

Need the fiberglass top for a 1975 fj40. I am located in charlotte NC........DOes anybody have this?

 

[NorCalDoug]

I learned about the 91/92 difference in a round-about way. I was looking for mud flaps at one time and was ready to get a pair from a FJ80, but learned that they wouldn't fit.