For Sale 66' FJ40 Maryland $7000

Hate to let it go but I need to change it up a bit.

66' Cruiser semi restored.

70' F155 engine,
SM420 tranny
Dana300 twin sticked
centered Toy truck rear.
Front axle out of a 76' with fine spline birfields, toy truck stuff from knuckles out.
Disk brakes all around, corvette master cylinder.

Warn M8000. Custom cage, long jump seats. As you can see in the buildup I have went through everything. poly tank, heater works, all gauges, switches rubber seals, emblems are there and in great shape. Complete truck. No parts needed. just some love. I measured prior to cage build and a besttop or Paki top will still go on with the cage in place. No top now though. Tonneau cover only.

link to buildup on here.

https://forum.ih8mud.com/40-55-series-tech/32996-got-my-first-fj40-pics-info.html

Will need to get some updated pics. The swampers have been swapped with a more road friendly tire.

The only bad.

I have wheeled it a couple of times and has some dings and dents.
The tranny could use a rebuild. Pops out of 3rd. oil pan is leaking. Need to get a battery before purchase.

I have almost all the stuff for a power steering conversion using Toy box and bracket. Just need a pump. Have all the hoses and all.


I have alot of spares as well as pieces and parts. car cover, tie rods, birfields,

Looking to get a 97-98 4runner. Will trade for the right one. Will get more info for any serious buyers.

Still a great truck. only minor things to do to make it top notch. I have too many projects at the moment.



$7000 obo.

jamisonworkshop@hotmail.com

Thanks,

Mike

 

[miko]

Nice looking rig. Would love to see pics of how it sits on the new tires. Are the jumps seats belted? Did you end up pulling the tub? Couldn't quite tell from the build up thread.

 

[Jamison Workshop]

I did not put any belts for the rear seats. Easy enough to do. I did everything but pull the tub.
Body mounts were not pulled. I did wire wheel and paint the frame from underneath though.

Truck actually came from North Carolina from the registration I found in it when I got it.

Frame and body are solid. Rear wheel wells uncut.

I will get some pics up with new tires. They are 32x 11.50.

 

[miko]

Would definitely love to see more pics. One other question - how wide are the jump seats? Wide enough for 2 younger kids to sit for a few minute ride in town?

 

[masterfab23]

Interested in a locked 96
https://forum.ih8mud.com/vehicles-trailers-sale-wanted/520844-feeler-my-locked-96-your-60-a.html

Sent from my HTC EVO4G using IH8MUD

 

[Jamison Workshop]

The jump seats are the longest version. I wanted as much room as possible when I did it. I believe I am the only one I know of to fit long jump seats and a cage together and make it fit. Very tough as you can see the bar has to go through the bracing. THey do come out easy enough though.

More recent pics.
Nothing has really changed. I need to get a battery and get it fired up.
Tires have lots of tread.

I will get pics of the dents. front driver fender has a dent as well as one on the cowl. Both fixable. Paint on rockers is cracking from the running boards being pushed up.

some leaking oil from pan but all in all in good shape.

 

[Jamison Workshop]

One other thing I will say is since I built this up in only has ~300 miles on it.

All things replaced with new or repro in buildup

brand new windshield and rubber
flywheel
clutch
all lights
bumperettes
all emblems
latches
seals, rubber gaskets
wheels
hubcaps
full tune up
radiator hoses
master cylinder
brakes
brake lines
front bib
seat covers
battery tray
all wiring
fuel pump
gas tank
tank filler

I also do have a DUI distributor. Need different plug wires. That will get rid of the flat spot off of idle.
factory retard distributor in it now.

 

[Jamison Workshop]

Sale Pending

 

[KruiserK]

Congrats! I love that 40

 

[miko]

Congrats! I love that 40

Me too. If only the wife would have given the green light. <sigh>