1982 FJ60 brown ext/int Utah

[cruiser ken]

Location

United States

Do not contact this account, I now use MOTOV8R.
Exterior is dark brown, interior is brown, located at zip 84045

AVAILABLE:
front turn signals
rear turn signals
exterior parts are mostly rust - probably not much good
some seat parts
dash pad is cracked but useable
gauges
all types of hardware, door, tailgate, etc
interior parts
tranny/tcase - $200 (seperate tranny $75 tcase $125)
OME lift springs - $150 includes shocks 3/4 are good 1 is bad. no shackles.
pedal assy
clutch master


NOT AVAILABLE parts:
Motor
motor accessories
ps gearbox
rear heater switch
rear defrost switch
rear cargo panels
Passenger seat bottom cushion/cover
front driveshaft
center console
toyota grill emblem
Grill




Ask me, see if I have it. Help me, help you. Thanks.

 

[cruiser ken]

pics, can get pics of interior, dash, etc, just ask... thanks.

 

[Butt Ugly Chuck]

Mulling the springs , but not ready to jump in line just yet... What kind of shape they in?

Good luck!
Butt

 

[cruiser ken]

They are rusty, I think they are still very useable though, they ride very nice. I can get some pics once I get them pulled.

 

[ginericLC]

Ken,

I need a rear defroster switch, rear heater switch (both with pigtails if available) and a PS front seat bottom cushion and cover. If you are going to cut the body up I might want the fuel door and about 2" of the surrounding body (I might need to relocate my fuel door to the DS side on my project)

Eric V.

 

[robj]

Ken, I need the front drive shaft, do you have it still? PM me w/ price Thanks Rob

 

[kblomquist]

Interested!

PM'd ya.

 

[cruiser ken]

PMs sent to every one.

 

[cruiser ken]

updated the parts list

 

[RredFJ40]

What condition is the dash switch surround in? The plastic piece that goes around the heater controls/ashtray etc. Looking for one that isn't cracked around the screw holes.

 

[cruiser ken]

What condition is the dash switch surround in? The plastic piece that goes around the heater controls/ashtray etc. Looking for one that isn't cracked around the screw holes.

I threw it out, it had been hacked on to add switches and was broken on the thin piece above the heater, sorry.

 

[RayN]

Possibly interested in the tranny and transfer. How much?

Ray

 

[PhilC64]

Interested in the hubs if you still have em.

 

[Rigger]

I need one hub if Phil wouldn't mind sharing!

 

[PhilC64]

I need one hub if Phil wouldn't mind sharing!

I'll send you my Selectros so you can have 2 hubs!

 

[red_dirt_okie]

I am interested in the seats if they match my interior. Do you have pics? I am looking for a good dash cover/pad but I didn't see it in the list?

 

[cruiser ken]

I haven't pulled the hubs yet, but I can.

Passenger seat bottom has been sold.
Driver seat bottom is pending sale.

Dash pad has cracks.

 

[PhilC64]

Thanks Ken! Just Pm'd you

 

[fowldarr]

Where is Saratoga Srpings Utah, I need a drivers side exterior door handle, carb, and might be interested in the springs. I'll be in SLC this weekend. PM me if any of this is available, whether you're near SLC or not.

 

[Slowerthanu]

Where is Saratoga Srpings Utah, I need a drivers side exterior door handle, carb, and might be interested in the springs. I'll be in SLC this weekend. PM me if any of this is available, whether you're near SLC or not.

Saratoga is about 25 minutes south of SLC.


Cruiser Ken, how much for the pedal assembly (Clutch and Brake pedal bucket), Clutch master, line and slave?

Also, is the Bellhousing and flywheel for sale?

Dan