wheel

Is this just tediously difficult or am I doing something wrong. PO installed all cylinders on the wrong side - to tighten the cylinders I would start with the screwdriver angled away from the center of the wheel. I always adjusted with a screwdriver. I blew a cylinder, and decided to replace...

Like most northwest fj bj 60/62s ..the sheet metal corrodes from the acidic effects of rain. my wheel wells need to be cut out. The quarter panels need to be majorly repaired. The back tail light sheet metal is crunched in. The tail gate has a hole in it. The frame needs major work on inner c...

Has anyone ever done this before? Cut the cab just in front of the wheel wells and welded in some kind of back panel that gives the fj6o a truck look and attached a aluminum box? What would cost more in labor and part? Doing this or repairing both inner/outer wheel wells and quarter panels...

I went to get my truck inspected today (state of VA) and the inspection station rejected my vehicle because the passenger side front wheel had some "play". Sounds like wheel bearings? How can I remedy this? Thank you. 96 Landcruiser

Has anyone used the bell housing adapter from marks I am trying to decide which way to go I have a 72 40 with a smallblock and a three speed I am going to put a 4 speed in it

fj62: Looking for carpet in good condition for the rear cargo area , the entire vechile and the vinyl wheel well covers.

Hi, Mine is a '95 HZJ80 (Australian). Rear axle is full-float with discs. I was all set to do my rear wheel bearings on Tuesday (Anzac day holiday here), but got worried that I've been supplied front wheel kits instead of rear. Any one able to offer some advice before I start trying to force...

Sorry all, I didn't know if I should put this in the Axle/Suspension thread or here... I recently bought 2 sets (4) 1.5" spacers from NITROGEAR for $280. turns out I didn't like the look with my stock wheels. I only had them for a week... were on my 100 series for 3 days before I took them...

Hiya's! So, I apologize in advance if these ?'s seem elementary. I've been reading a bit here and it seems there's ten ways forward but not a most common path. I've decided the first mods to my newly acquired Pig will be knuckle maintenance, a modest lift, finding new center caps & putting...

I have three Rock Warrior Wheels I am interested in selling, individually. Wheels are in good shape with no curb rash. Red lettering of TRD caps is slightly faded. $250 + Shipping. Price is for each wheel.

$15 shipped

I have a 2000 Grand Am GT, I've noticed a random front end grinding noise that does it in a pattern. It will grind 2 times in a row then stop , then a few seconds later same thing. I can feel it on the floor / brake & gas peddle. I'm almost certain it's not a wheel bearing. I'm concerned...

selling my steering wheel out of my 1999 LC. its in fair condition, worn in some areas (see pix). perfect for someone that plans to rewrap. $50 obo picked up from socal 90650. text 562-883-8838

I am thinking that is the reason for skid control and alarm coming on. New rack and pinion. Mechanic did not see any obvious issues underneath but it did have ABS codes. Since he didn't find the rack or tie rods loose, I'm thinking wheel sensor...but still searching. Thanks

Title says it, what shocks have you guys used with a spring over conversion on a lwb truck, part numbers appreciated. Thanks Larry

I searched and searched but couldn't find anything. Does anybody have the part number for non hubcap 16x5.5" steel wheels? One-piece, not split.

SOLD On CL for $20 but $10 $5 picked up Mud price. Package deal with other stuff I'm selling here on Mud. Want this $%!&* thing gone! Has a 35 inch BFG AT mounted on it that has a lot of tread but its desiccated. Holds air for a little while and a shot of that green Tire Slime type stuff...

Re: Cargo area storage - Does anybody know the width between the wheel humps in the cargo area of a 60? I'd like to start working on cargo area storage cabinet but am not near my rig and my rig is full of crap. Thanks! Rob

(I'm getting some fresh meat installed on Friday (265/70-18 Grabber AT2s and I'll be doing my small lift in the next few weeks. ) Is anyone running wheel spacers on their GX? Im contemplating going with a set of 1.5" SpiderTrax spacers to help widen the stance. Anyone running a set? Any...

So I've got a set of 4 of some type of old wagon wheels on my FJ40, maybe custom 70/80 Series U.S. Wheels, I can't tell. They're 15x8 with 3.25" of backspacing that the PO rattle canned black. There's no identifying marks, stamps, tags, labels, etc anywhere on the wheels that I can find. I'm...